Commands Menu; Installation - Icar RPC 8BGA Manuel Complet

ICAR PQS
Nr Measure code
26 W TOT
27 var TOT
28 VA TOT
29 Cosphi TOT
30 Senphi TOT
31 THD VLN MAX
32 THD I MAX
33 THD VLL MAX
34 H. VLN MAX
35 H. I MAX
36 H. VLL MAX
37 Cosphi MAX
38 Senphi MAX
39 VLN MAX
40 I MAX
41 VLL MAX
42 VLN MIN
43 VLL MIN
44 Cosphi MIN
45 AIN
46 CNT

25 COMMANDS MENU

The commands menu allows executing some occasional operations like reading peaks resetting, counters clearing, alarms reset,
etc. If the Advanced level password has been entered, then the commands menu allows executing the automatic operations useful
for the device configuration. The following table lists the functions available in the commands menu, divided by the access level
required.
COD. COMMAND
C01 Reset partial Energy meter
C02 Reset CNTx counters
C03 Reset LIMx status
C04 Reset max temperature
C05 Reset max overload
C06 Reset step hour meter
C07 Reset step switching counters
C08 Step power restore
C09 Reset total Energy meter
C10 TEST mode activation
C11 Event log reset
C12 Setup to default
C13 Backup setup
C14 Restore setup
C15 Reset weekly TPF
C16 Reset maintenance interval 1 counter
C17 Reset maintenance interval 2 counter
C18 Reset maintenance interval 3 counter
C19 Reset max values
Once the required command has been selected, press  to execute it. The device will prompt for a confirmation. Pressing □
again, the command will be executed. To cancel the command execution press ◄. To quit command menu press ◄.

26 INSTALLATION

8BGA is designed for flush-mount installation. With proper mounting, it guarantees IP54 front protection.
Insert the device into the panel hole, making sure that the gasket is properly positioned between the panel and the device front
frame. From inside the panel, for each four of the fixing clips, position the clip in its square hole on the housing side,then move it
backwards in order to position the hook.
Description
Total active power
Total reactive power
Total apparent power
Cosphi (balanced three-phase system)
Senphi (balanced three-phase system)
THD phase voltage (max among phases)
THD phase current (max among phases)
THD phase-phase voltage (max among phases)
Harmonic content of order n of phase voltage (maximum among phases)
Harmonic content of order n of phase current (maximum among phases)
Harmonic content of order n of phase-phase voltage (maximum among phases)
Cos-phi (max among phases)
Sen-phi (max among phases)
Phase voltage (max among phases)
Current (max among phases)
Phase-phase voltage (max among phases)
Phase voltage (min among phases)
Phase-phase voltage (min among phases)
Cos-phi (min among phases)
Measure from analog inputs
Programmable counter
ACCESS LEVEL
Usr
Usr
Usr
Adv
Adv
Adv
Adv
Adv
Adv
Adv
Adv
Adv
Adv
Usr
Usr
Usr
Usr
Usr
Usr
49 / 86
DESCRIPTION
Resets partial energy meter
Reset programmable counters CNTx
Reset status of latched LIMx variables
Reset maximum temperature peak value
Reset maximum overload peak value
Reset step operation hour meters
Reset step operation counters
Reload originally programmed power into step trimming
Resets total energy meters
Enables the TEST mode operation for output operation verifying
Clears the event history log
Resets setup programming to default
Makes a backup copy of factory or user setup parameters settings
Reloads setup parameters with the backup of factory or user
settings.
Reset weekly true power factor value
Resets maintenance interval 1 counter
Resets maintenance interval 2 counter
Resets maintenance interval 3 counter
Resets recorded max vlaues
rev9 jan19