Electrical Safety - Black & Decker KS501 Mode D'emploi

ENGLISH
in accordance with a standard test method provided by
EN 62841 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.

Electrical safety

#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch (KS701E, KS701PE) or On/Off
switch (KS501)
2. Lock-on button
3. Saw blade locking lever
4. Shoe plate
5. Dust extraction outlet (KS701E and KS701PE only)
6. Pendulum stroke (KS701PE only)
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped. Used saw blades may be hot.
Fitting the saw blade (fig. A - KS701E and KS701PE)
Hold the saw blade (7) as shown, with the teeth facing
u
forward.
6
(Original instructions)
Push the locking lever (3) away from the shoe plate (4).
u
Insert the shank of the saw blade into the blade holder (8)
u
as far as it will go.
Release the locking lever (3).
u
Fitting the saw blade (fig. A - KS501)
Before fitting or removing the saw blade (7) the saw blade
u
support roller (17) must be adjusted to the rear position so
that it does not contact the blade.
Loosen (do not remove) the two screws (18).
u
Hold the saw blade (7) with the teeth facing forward.
u
Insert the shank of the saw blade (7) into the blade holder
u
(8) as far as it will go.
Slightly tighten the two screws (18) alternately to position
u
the blade, then fully tighten the two screws (18).
Adjust the saw blade support roller (17) as described
u
above.
To remove the saw blade (7), turn both screws (18) one
u
turn counterclockwise.
Connecting a vacuum cleaner to the tool (fig. B -
KS701E and KS701PE only)
Slide the vacuum nozzle (9) into the dust extration
u
outlet (5).
Use
Adjusting the shoe plate for bevel cuts (fig. C)
Warning! Never use the tool when the saw shoe plate is loose
or removed.
The shoe plate (4) can be set to a left or right bevel angle
of 45°.
Loosen the screws (10). Some models have one screw.
u
Pull the shoe (4) forward, rotate the shoe to the left or
u
right and push it back into the 45° location. (KS701E and
KS701PE only).
Push the shoe (4) back, rotate to the right and pull it back
u
into the 45° location. (KS501 only).
Tighten the screw.
u
To reset the shoe plate (4) for 90° cuts:
Loosen the screw (10).
u
Pull the shoe (4) forward, rotate to the centre and push it
u
back into the 0° location.
Tighten the screw.
u
Variable speed control (KS701E and KS701PE only)
Use a high speed for wood, medium speed for aluminium
u
and PVC and low speed for metals other than aluminium.
Switching on and off
To switch the tool on, press the variable speed switch
u
(KS701E and KS701PE) or the On/Off switch (KS501) (1).