Adding Or Removing Devices; Memorising Additional Devices; Optional Photocells Addition; Memorising Additional Transmitters - Nice Maestro300 Instructions Et Avertissements Pour L'installation Et L'utilisation

9.1.3.2 - Open input configuration - OGI output configuration - Discharging of Motor 1 and 2 upon closing - Discharging of Motor 1 and
2 upon opening
Before proceeding, check the parameter to be modified in Table 7 and the action to be performed:
01. On the transmitter (Fig. 24) simultaneously press and hold keys T1 and T3 for 5 seconds then release them.
02. Within 3 seconds from releasing them, perform the action specified in Table 7 to verify the desired parameter.
03. Release the key when the flashing light starts flashing: count the flashes.
Check in Table 5 the value corresponding to the number of flashes.
Parameters
Open input configuration
OGI output configuration
Discharging of Motor 1 and 2 upon closing
Discharging of Motor 1 and 2 upon opening

9.2 - ADDING OR REMOVING DEVICES

It is possible to add or remove devices at any time to the system: if devices are added, it is important to verify that these are perfectly compatible with
MAESTRO 200; for further details contact the Nice technical support service.

9.2.1 - Memorising additional devices

The recognition operation of the devices connected to the ECSbus and to the Stop input is usually car-
ried out during the installation phase; but if devices are added (or removed) subsequently, the following
procedure must be carried out:
01. On the control unit press and hold button P2 (Fig. 25) for at least 3 seconds then release it.
02. Wait a few seconds for the control unit to end learning the devices: led L2 lights up. If it flashes there
is some error, see chapter 10.
03. After adding or removing devices, the automation must be tested again (Par. 6.1).

9.2.2 - Optional photocells addition

At any time, you can install additional photocells in addition to those already provided as standard with MAESTRO300. In an automation with gates with
2 leaves, it is possible to place them according to the representation in fig. A.
For correct photocells recognition by the control unit, you need to carry out its addressing, through the use of suitable electrical jumpers. The addres-
sing operation must be carried out both on TX and RX (setting the electrical jumpers in the same way) and by making sure there are no other couples
of photocells with the same address. The photocells addressing serves both for correct recognition by other devices on the ECSbus, and to assign the
function performed.
01. Open the photocell housing.
02. Locate the position in which they are installed according to Figure A and install the jumper according to Table C.
The unused jumpers are stored in a compartment on their reserve, to be able to be reused in the future(fig. B).
03. Carry out the recognition phase as described in paragraph 5.3 "Memorisation of connected devices".
TABLE C
Photocells
External photocell h = 50 activated during the
FOTO
closing phase (stops and reverses the gate's
(PHOTO)
movement)
External photocell h = 100 activated during
FOTO II
the closing phase (stops and reverses the
(PHOTO II)
gate's movement)
Internal photocell h = 50 cm with activation
FOTO 1 both during closing (stops and reverses the
(PHOTO 1) movement) and during opening (stops and
restarts when the photocell disengages)
Internal photocell h = 100 cm with activation
FOTO 1 II
both during closing (stops and reverses the
(PHOTO
movement) and during opening (stops and
1 II)
restarts when the photocell disengages)
Internal photocell triggered during the
FOTO 2
opening phase (stops and reverses the
(PHOTO 2)
gate'smovement)
FOTO 2 II Internal photocell triggered during the
(PHOTO opening phase (stops and reverses the gate's
2 II) movement)

9.3 - MEMORISING ADDITIONAL TRANSMITTERS

The control unit incorporates a radio receiver for ECCO5 transmitters (various models). The transmitters supplied are not memorised, therefore it is first
necessary to memorise the 1st transmitter (Par. 5.5); to memorise additional transmitters, it is possible to choose one of the procedures (Mode 1 or
Mode 2) indicated below. The control unit can memorise a total of 100 units: memorisation in Mode 1 occupies one unit of memory for each transmitter,
while the Mode 2 procedure occupies one unit of memory for each transmitter key.
Before carrying out the memorisation procedures, we recommend reading them and observing the indicated times.
TABLE 7
Actions to be performed
Press and hold key T1
Press and hold key T2
Press and hold key T3
Press and hold key T4
Jumpers
24
25
A
F A 2
O II
F O T
O
F O T
F O T
O 2 II
B
T1
T3
F O T
O 2
O 1 II
F O T
O 1
F O T
F A 1
English – 25