Mode 1 Memorisation Procedure; Mode 2 Memorisation Procedure; Memorisation Procedure Near The Control Unit With Two Transmitters; Deleting The Memory Of The Individual Transmitter From The Control Unit's Memory - Nice Maestro300 Instructions Et Avertissements Pour L'installation Et L'utilisation

9.3.1 - Mode 1 memorisation procedure

This procedure allows for simultaneously memorising all the transmitter keys, by automatically pairing them to the commands shown in Table 6.
A transmitter memorised in Mode 1 can control only a single automation.
TABELLA 8
Tasti Comando abbinato
T1 Passo Passo
T2 Apertura parziale
T3 Solo apre (apre-stop)
T4 Solo chiude (chiude-stop)
T5 Courtesy light ON-OFF
Memorisation procedure
01. On the control unit (Fig. 27) press and hold key P1 for at least 3 seconds; when led L1 switches on, release the key.
02. Within 10 seconds from releasing it, press and hold for 3 seconds any key of the transmitter to be memorised.
If the memorisation procedure was successful, led L1 (on the control unit) will flash 3 times.
03. To memorise other transmitters, repeat step 02 within the next 10 seconds otherwise the memorisation phase will terminate automatically.

9.3.2 - Mode 2 memorisation procedure

This procedure allows for memorising one key at a time, by pairing one of the desired commands shown in Table 9.
A transmitter memorised in Mode 2 can control multiple automations (for example: automation 1 controlled by key 1; automation 2 controlled
by key 2; and so forth)
No. of key Paired command
presses
once Step-by-step
twice Pedestrian opening
3 times Open only
4 times Close only
5 times Stop
6 times Condominium open
7 times High priority open
8 times Pedestrian opening 2
9 times Pedestrian opening 3
10 times Open + lock automation
11 times Close + lock automation
12 times Lock automation
13 times Release automation
9.3.3 - Memorisation procedure near the control unit with two transmitters (without using the control unit keys)
With this procedure a NEW transmitter is memorised using a second transmitter (OLD) already memorised and operating, without using the keys of
the control unit but drawing close to the latter.
During the procedure the NEW transmitter is memorised in the same way that the OLD transmitter was memorised (Mode 1 or Mode 2).
• Procedure with OLD transmitter memorised in Mode 1:
01. Draw near the control unit with the two transmitters:
02. On the NEW transmitter, press and hold any key for at least 8 seconds then release it.
03. On the OLD transmitter, press and hold any key to be copied for at least 2 seconds then release it.
04. On the OLD transmitter, press and hold any key to be copied for at least 2 seconds then release it.
05. On the OLD transmitter, press and hold any key to be copied for at least 2 seconds then release it.
06. On the NEW transmitter, press and hold any key to be memorised for at least 5 seconds then release it.
Repeat the procedure for each transmitter to be memorised.
• Procedure with OLD transmitter memorised in Mode 2:
01. Draw near the control unit with the two transmitters:
02. On the NEW transmitter, press and hold the key to be memorised for at least 8 seconds then release it.
03. On the OLD transmitter, press and hold the key to be copied for at least 2 seconds then release it.
04. On the OLD transmitter, press and hold the key to be copied for at least 2 seconds then release it.
05. On the OLD transmitter, press and hold the key to be copied for at least 2 seconds then release it.
06. On the NEW transmitter, press and hold the key to be memorised for at least 5 seconds then release it.
Repeat the procedure for each transmitter to be memorised.

9.4 - DELETING THE MEMORY OF THE INDIVIDUAL TRANSMITTER FROM THE CONTROL UNIT'S MEMORY

This procedure allows cancelling a single transmitter (memorised in Mode 1) or only one of its keys (memorised in Mode 2): it is necessary
to have the transmitter to be cancelled and simultaneously be able to access the control unit.
• Procedure with transmitter memorised in Mode 1:
01. On the control unit (Fig. 28) press and hold key P1 until the end of the procedure.
26 – English
26
TABLE 9
No. of flashes of led
L1 on the control
unit
1
2
3
4
5
6
7
8
9
10
11
12
13
wait 1 second between two successive steps.
wait 1 second between two successive steps.
LED
T5
T1
T2
T3 T4
Memorisation procedure
01. Before proceeding, it is necessary to cancel the memory of
the transmitter to be memorised – see Par. 9.4.
02. In Table 9, choose the command and the number of press-down
actions to be effected on the desired transmitter key.
03. On the control unit (Fig. 27) press and release key P1 for a
number of times corresponding to the chosen command (Table
5); led L1 must emit a number of fast flashes corresponding to the
chosen command.
04. Within 10 seconds, press and hold for 2 seconds the key of the
transmitter to be memorised: if the memorisation was successful,
led L1 (on the control unit) will flash 3 times.
05. To memorise other transmitters, with the same command, repeat
step 03 within 10 seconds, otherwise the memorisation phase will
terminate automatically.
Note: the T5 key is not suitable for memorisation in Mode 2.
27