Nice Maestro300 Instructions Et Avertissements Pour L'installation Et L'utilisation page 35

CONTENTS
1 GENERAL WARNINGS: SAFETY - INSTALLATION
QUICK GUIDE (images only)
2 PRODUCT DESCRIPTION
3 INSTALLATION
3.1 VERIFYING THE SUITABILITY OF THE GATE AND ENVIRONMENT
3.2 VERIFYING THE PRODUCT'S APPLICATION LIMITS
3.3 PRODUCT TECHNICAL SPECIFICATIONS
3.4 PRE-INSTALLATION WORKS
3.5 INSTALLING THE MAESTRO GEARMOTORS (models 300M/300C)
3.5.1 INSTALLING THE MAESTRO GEARMOTORS 300
3.5.2 ADJUSTMENT OF THE MECHANICAL OPENING LIMIT SWITCH
3.6 INSTALLING THE PHOTOCELLS model PH200
3.7 INSTALLING THE FLASHING LIGHT model FL200
4 ELECTRICAL CONNECTIONS
4.1 ELECTRICAL CONNECTION TO THE CONTROL PANEL
4.2 CONNECTION OF THE MAESTRO300C and MAESTRO300M GEAR MOTORS
4.3 POWER SUPPLY CONNECTION
5 PROGRAMMING
5.1 CONTROL UNIT KEYS
5.2 INITIAL CHECKS
5.3 MEMORISATION OF CONNECTED DEVICES
5.4 MOTOR TYPE SELECTION
5.5 MEMORISATION OF GATE LEAF OPENING AND CLOSING ANGLES
5.6 MEMORISATION OF THE 1
5.7 BASIC ADJUSTMENTS
5.7.1 Choosing the gate leaf manoeuvre speed
5.7.2 Choosing the operating cycle of the gate leaf manoeuvre
6 TESTING AND COMMISSIONING
6.1 TESTING
6.2 COMMISSIONING
7 MAINTENANCE
8 PRODUCT DISPOSAL
9 FURTHER INFORMATION
9.1 ADVANCED ADJUSTMENTS
9.1.1 Adjusting the parameters using the transmitter
9.1.1.1 Parameter adjustment procedure: Pause time - Pedestrian opening - Motor force - Step-by-Step function
9.1.1.2 Parameter adjustment procedure: SbS input configuration - Flash output configuration - Discharging of Motor 1
and 2 upon closing - Discharging of Motor 1 and 2 upon opening
9.1.2 Presence function
9.1.3 Verifying the values set for each parameter (using the transmitter)
9.1.3.1 Parameter verification procedure: Pause time - Pedestrian opening - Motor force - Step-by-Step Function
9.1.3.2 Parameter verification procedure: Discharging of Motor 1 upon closing - Discharging of Motor 1 upon opening -
Discharging of Motor 2 upon closing - Discharging of Motor 2 upon opening
9.2 ADDING OR REMOVING DEVICES
9.2.1 Memorising additional devices
9.2.2 Optional photocells addition
9.3 MEMORISING ADDITIONAL TRANSMITTERS
9.3.1 Mode 1 memorisation procedure
9.3.2 Mode 2 memorisation procedure
9.3.3 Memorisation procedure near the control unit with two transmitters
9.4 DELETING THE MEMORY OF THE INDIVIDUAL TRANSMITTER FROM THE CONTROL UNIT'S MEMORY
9.5 COMPLETE DELETION OF THE RADIO MEMORY
9.6 INSTALLING THE BACK-UP BATTERY
9.7 INSTALLING THE SOLAR POWER SYSTEM KIT model SOLEKIT
9.8 DIAGNOSTICS AND DEVICE SIGNALS
9.8.1 Photocell signals
9.8.2 Flashing light signals
9.8.3 Control unit signals
9.9 SPECIFICATIONS
9.9.1 ECSbus system
9.9.2 Stop input
10 TROUBLESHOOTING
11 Essential safety requirements (detachable insert)
ANNEX I (detachable insert)
EC Declaration of Conformity
ST TRANSMITTER
3
6
16
16
16
16
16
17
18
18
18
19
19
19
19
19
19
19
19
19
20
20
21
21
22
22
22
22
22
23
23
23
23
23
23
24
24
25
25
25
25
25
25
25
26
26
27
27
27
27
27
28
28
28
29
29
30
29
29
30
A
B
C
English - 15