Connecting A Video Switcher; Turning On The Power - Sony RM-IP10 Mode D'emploi

Connecting a video switcher

Use a commercially available contact-control type video
switcher to switch between the multiple camera signals
to be output.
1 2 3
1 2 3 4 5 6 7 8 9
IR SELECT
VISCA RS-422 OFF ON HD SD
75
IN VISCA RS-232 OUT EXT SYNC IN VIDEO S VIDEO SDI OUT
VISCA
RS-232C IN
RS-232C cable
VISCA RS-232C
(commercially
OUT
available)
Second
1 2 3
1 2 3 4 5 6 7 8 9
IR SELECT
BRC-H900
VISCA RS-422
OFF ON HD SD
75
IN VISCA RS-232 OUT EXT SYNC IN VIDEO S VIDEO SDI OUT
VISCA
RS-232C IN
RS-232C cable
(commercially
VISCA RS-232C
available)
OUT
First
1 2 3
1 2 3 4 5 6 7 8 9
IR SELECT
BRC-H900
VISCA RS-422 OFF ON HD SD
75
IN VISCA RS-232 OUT EXT SYNC IN VIDEO S VIDEO SDI OUT
VISCA
RS-232C
RS-232C IN
cable
(commercially
available)
to the AC adaptor
(supplied)
VISCA RS-232C
MODE LAN RS-232C RS-422 TALLY/CONTACT
VISCA
1 9 1 9
TALLY/CONTACT (For
details, see the
explanation of ea DIP
1 switch 4 and 5 on
page 9.)
CONTACT
Video switcher (commercially available)
For connection with a video switcher, refer to the
Operating Instructions of the switcher.
Third to seventh
BRC-H900
RGB/COMPONENT
DC IN 12V
to the AC adaptor
RGB/ COMPONENT
to the AC adaptor
RGB/COMPONENT
DC IN 12V
to RGB/
COMPONENT
to the AC
adaptor
RGB/COMPONENT
DC IN 12V
to RGB/
COMPONENT
!
DC 12V
to

Turning on the Power

1 2
JOYSTICK
VALUE LOCK
BLACK PAN-TILT
POSITION GROUP
LIGHT RESET
KNOB
RESET
– +
R
PRESET GROUP POSITION
MODE
BRIGHT
1 2 3 4
SHIFT
9 10 11 12
GROUP
– +
B
SELECT
CAMERA
AUTO
FOCUS
AUTO 1 2 3 4
POWER
MANUAL
ONE PUSH
NEAR FAR AF
POWER CAMERA
1
Connect the camera to an AC outlet.
The power of the camera is turned on and the
POWER lamp lights.
The camera will automatically pan, tilt, and be reset
to the position stored in POSITION 1 (Pan/tilt reset
action).
2
Press the 1 switch on the unit to turn it on.
When the unit is turned on, buttons and indicators
flash as follows:
Yellow (1 second) t Green (1 second) t Red (1
second) t The GROUP/POSITION button that
was selected when the unit was turned off last (with
the upper or lower indicator beside of the SHIFT
button and GROUP indicator) and the CAMERA
button (2 seconds)
Then, the CAMERA button representing the
camera whose power was turned off last, lights.
(CAMERA 1 button lights by default.)
When connecting over a LAN, the unit starts with
the last camera group is selected.
3
Turn on the peripheral devices.
Notes
• Be sure to turn on the power of the camera before the
power of this unit. Otherwise, the unit cannot
recognize the connected camera.
• Do not touch the joystick when turning on the power
of the unit. Doing so may affect the confirmation of
the origin.
ONE PUSH
MENU
AWB
5 6 7 8
13 14 15 16
5 6 7
Turning on the Power
17
GB