EINHELL RT-TS 1825U Mode D'emploi D'origine page 17

Anleitung_RT_TS_1825_U_SPK1:-
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembling the base frame (Fig. 17/18)
Turn the saw upside down and place it on the
floor.
Use the hex screws and nuts to fasten the four
wide side struts (41) loosely to the saw.
Now screw the four legs (40) loosely to the wide
side struts.
Then screw the four narrow side struts (42)
loosely to the four legs (40) and mount the
rubber feet (43) on the legs.
Important! The shorter narrow struts (No. 2)
have to be used on the sides.
Finally, turn the saw together with the base
frame upright and tighten all the screws and nuts
(Fig. 18).
Screw the additional legs (A) to the rear legs
(40) so that they point towards the rear of the
machine (Fig. 28).
7.2 Table width extension and length extension
7.2.1 Length extension table (Abb. 19/20)
Use the hex screws and nuts to fasten the table
length extension (36) loosely to the saw table (1)
Screw the supports (50) loosely onto the saw
housing and onto the table length extension.
Align the table length extension level with the
saw table (1).
Finally, tighten all screws and nuts.
7.2.2 Width extension tables (Abb. 21/22)
Slide the width extension tables by their
connecting tubes into the prepared mounts as
far they will go, making sure that the numerical
scale always faces the front of the machine.
Secure the width extension tables in place with
the clamping screws (21) underneath.
7.3 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (44) in the
splitter.
Do not tighten the screw (15) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
13.07.2010 12:31 Uhr Seite 17
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.4. Setting the splitter (Fig. 3/6/7/8)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place.
Remove the saw blade guard (see 7.3).
Take out the table insert (6) (see 7.5).
Slacken the fixing screw (20).
7.4.1. Setting for maximum cuts (Fig. 6/7/8)
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) equals approx. 10 cm.
The distance between the blade (4) and the
splitter (5) should be 3-8 mm.
Retighten the screw (20) and mount the table
insert (6) (Fig. 7).
7.5 Changing the table insert (Figure 7)
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2).
Remove the 2 countersunk head screws (34).
Take out the worn table insert (6).
To fit the replacement table insert, proceed in
reverse order.
7.6 Fitting/replacing the blade (Fig. 5)
Important! Pull out the power plug first.
Remove the table insert by undoing the two
countersunk head screws (see 7.5).
Undo the nut with a size 24 wrench on the nut
itself and a second fork wrench (size 13) on the
motor shaft to apply counter-pressure.
Important! Turn the nut in the direction of
rotation of the saw blade.
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the blade
at an angle.
Clean the blade flange thoroughly before fitting
the new blade.
Mount and fasten the new saw blade in reverse
order.
Important! Note the running direction. The
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
Refit and set the splitter (5) and the saw guard
(2) (see 7.3., 7.4.)
Check to make sure that all safety devices are
properly mounted and in good working condition
GB
17