Items Supplied; Safety Information - EINHELL BT-EW 160 Mode D'emploi D'origine

Masquer les pouces Voir aussi pour BT-EW 160:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
Anleitung_BT_EW_160_SPK1:_
GB
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety regulations with due care. Keep this manual in
a safe place, so that the information is available at all
times. If you give the equipment to any other person,
hand over these operating instructions and safety
regulations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.
1. Layout (Fig. 1)
1. Electrode holder
2. Earth terminal
3. Adjustment wheel for welding current
4. Selector switch 230 V / 400 V
5. Control lamp for overheating
6. Welding current scale
7. Carry handle
8. Power cable 400 V
9. 230 V mains cable

2. Items supplied

Welding set
Welding screen
3. Important information
Please read the directions for use carefully and
observe the information provided. It is important to
consult these instructions in order to acquaint
yourself with the machine, its proper use and safety
precautions.

Safety information

Please note
IMPORTANT
Only use this appliance for the purpose for which it is
designed and as described in these instructions:
Manual arc welding with coated electrodes.
Handling this system incorrectly may be hazardous
for persons, animals and property. The user of this
system is responsible for his/her own safety and for
the safety of others.
Read these operating instructions and follow all the
regulations.
10
04.06.2009
15:30 Uhr
Seite 10
Repairs and/or maintenance work may only be
carried out by qualified personnel.
Use only the power cables and welding cables
supplied. (16 mm
cables)
Ensure that the appliance is looked after properly.
To ensure that sufficient air can be drawn in
through the ventilation slits, the appliance should
not be constricted or placed next to a wall while it
is operating. Make sure that the appliance is
correctly connected to the mains supply (see 6.).
Do not subject the mains lead to any tensile
stress. Unplug the appliance before you change
its position.
Check the condition of the welding cables, the
electrode tongs and the earth terminals (-); wear
on the insulation and the live parts may result in
dangerous conditions and reduce the quality of
the welding work.
Arc welding generates sparks, molten metal
particles and smoke, so the following is required:
Remove all inflammable substances and/or
materials from the working area.
Ensure that there is adequate ventilation.
Do not weld on tanks, vessels or pipes that have
contained inflammable liquids or gases. Avoid all
direct contact with the welding circuit; the idling
voltage between the electrode tongs and the earth
terminal (-) may be dangerous.
Do not store or use the appliance in wet or damp
conditions or in the rain.
Protect your eyes with specially designed goggles
(DIN level 9-10), which you can attach to the
supplied safety shield. Wear gloves and dry safety
clothing that are not contaminated by any oil or
grease to ensure that your skin is not exposed to
ultraviolet radiation from the arc.
Do not use this welder to defrost pipes
Remember.
The radiation from the arc can damage your eyes
and cause burns on skin.
Arc welding generates sparks and droplets of
molten metal; the welded workpiece may start to
glow and will remain very hot for a relatively long
period of time.
Arc welding releases vapors that may be harmful.
Every electric shock is potentially fatal.
Do not approach the arc within a radius of 15 m
unprotected.
Protect yourself (and others around you) against
the possible hazardous effects of the arc.
Warning: Depending on the mains connection
conditions at the connection point of the welding
set, other consumers connected to the mains may
suffer faults.
2
rubber-sheathed welding

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

15.460.40

Table des Matières