Safety Regulations; Layout And Items Supplied; Intended Use - EINHELL BT-GW 190D Mode D'emploi D'origine

Appareil à souder au gaz inerte
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 26
Anleitung_BT_GW_190_D_SPK1__ 24.01.13 15:07 Seite 19
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety regulations with due care. Keep this manual in
a safe place, so that the information is available at all
times. If you give the equipment to any other person,
hand over these operating instructions and safety
regulations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be found
in the enclosed booklet.
2. Layout and items supplied (Fig. 1-8)
1. Handle
2. Operating status indicator
3. Thermostat control lamp
4. Housing cover
5. Gas bottle support surface
6. Castors
7. Welding current switch
8. ON/OFF/Voltage selector switch
9. CeCon plug
10. Earth terminal
11. Hose package
12. Gas nozzle
13. Burner
14. Guide rollers
15. Chain hook
16. Gas supply connector
17. Welding screen
18. Shielding gas hose
19. Pressure reducer
20. Pressure gage (gas flow rate)
21. Screw connector
22. Safety valve
23. Shielding gas hose connector
24. Rotary knob
25. Burner switch
26. 3 x contact pipe
27. Handle for housing cover
28. Safety chain
29. Welding wire speed controller
30. Adapter cable
31. Pressure gage (bottle pressure)
2.1 Assembly material
a. 16 x Screw for castors
b. 16 x Spring ring for castors
c. 16 x Washer for castors
d. 2 x Hose clip
k. 1 x Safety glass frame
l.
1 x Welding glass
m. 1 x Transparent safety glass
n. 2 x Safety glass retaining bushes
o. 3 x Nut for handle
p. 3 x Screws for handle
q. 2 x Safety glass retaining pin
r.
1 x Handle
s. 1 x Welding screen frame

3. Intended use

The shielding gas welding set is exclusively designed
for welding steel with the MAG (Metal Active Gas)
method using the appropriate welding wires and
gases.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Important information about the power
connection
This equipment falls under Class A of the standard
EN 60974-10, i.e. it is not designed for use in
residential areas in which the power supply is based
on a public low-voltage supply system because given
unfavorable conditions in the power supply the
equipment may cause interference. If you want to use
the equipment in residential areas in the which the
power supply is based on a public low-voltage supply
system, you must use an electromagnetic filter which
reduces the electromagnetic interference to the point
where the user no longer notices any disturbance.
In industrial parks or other areas in which the power
supply is not based on a public low-voltage supply
system the equipment can be used without such a
filter.
General safety information
It is the user's responsibility to install and use the
equipment properly in accordance with the
instructions issued by the manufacturer. If
electromagnetic interference is noticed, it is the user's
responsibility to eliminate said interference with the
technical devices mentioned in the section "Important
information about the power connection".
GB
19

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

15.749.90

Table des Matières