Software Update; Replacing The Blades - EINHELL FREELEXO+ Instructions D'origine

Ensure that no water can get into the interior
of the equipment.
•
For best results, clean the robot lawn mower
with a brush or rag.
•
Check the freedom of movement of the bla-
des (10) and the blade plate (11)
•
Use cleaning product for metal or very fine
abrasive paper to clean the charging contacts
on the robot lawn mower (1) and the charging
station (19). Clean them in order ensure effici-
ent charging.

7.2 Software update

If you want to update the software, copy the new
software to an empty USB stick. Make sure that
the rechargeable battery is fully charged before
you carry out the following steps.
1. Connect a USB stick to the USB connection
as shown in the illustration. (Fig. 11).
2. Switch on the main switch (7) (ON).
3. Press the POWER button (51) and the "OK"
button (54) at the same time. The robot lawn
mower will now start in boot mode.
4. Press the 3 key on the numeric keypad (57)
to start the update. The robot lawn mower
will then start updating the software and will
display the current progress as it does so.
Once the new software has been completely
copied, the robot lawn mower will switch to its
normal operating state.
5. Pull out the USB stick.
7.3 Maintenance
•
Worn or damaged blades (10) and their fas-
tening screws must always be replaced as a
set.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
•
Keeping your robot lawn mower in good
condition not only ensures a long lifespan
and high performance, but also enables the
equipment to thoroughly cut your grass with
minimal effort.
•
The blades (10) are subject to more wear and
tear than any other component. Therefore,
routinely check the condition of the blades
(10) and make sure that they are tightly fas-
tened. An excessively vibrating robot lawn
mower can indicate that the blades (10) are
damaged or have become deformed from
striking an object. If the blades (10) are worn
Anl_FREELEXO_plus_SPK9.indb 42 Anl_FREELEXO_plus_SPK9.indb 42
GB
or damaged, they must be replaced immedia-
tely.
•
There are no other parts inside the equipment
which require maintenance.

7.4 Replacing the blades

Only replace the blades with genuine blades, as
this will ensure top performance and safety.
The robot lawn mower is equipped with three bla-
des (10) fi tted to a blade plate (11). These blades
(10) have a service life of up to 3 months (if they
do not strike any obstacles). Please replace all
three blades (10) at the same time to ensure that
there is no possibility of any impairment to the
effi ciency and balance of your equipment.
To change the blades (10), proceed as follows
(Fig. 12):
1. Undo the fastening screws
2. Remove the blades (10) and replace them
with new ones. Always replace all three bla-
des (10) as a set.
3. Then retighten the fastening screw. Check
that the new blades (10) are able to rotate
freely.
Perform a general inspection of the robot lawn
mower at regular intervals and remove any depo-
sits which may have accumulated. At the start of
each season, ensure that you check the condition
of the blades (10). If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.
7.5 Repairing the perimeter wire
If the perimeter wire (18) gets severed at any
point, use the supplied cable connectors (16) to
repair it. To do so, insert both ends of the severed
perimeter wire (18) into the cable connector (16)
and squeeze it together with the help of a pair of
pliers. Connect the power plug to the socket out-
let. Then check whether it is working properly by
checking the LED indicator (21) on the charging
station (19).
- 42 -
14.11.2019 12:52:38 14.11.2019 12:52:38