Setup - Titan SPEEFLO PowrLiner 2850 Notice D'utilisation

Setup

Perform the following procedure before starting the engine of a
gas-powered line striper.
NOTE: The PL2850 comes in two versions, a one-gun
version and a two-gun version. all information
given in this manual applies to both units, except
where noted.
1. Ensure that the siphon hose and the return hose are
attached and secure.
2. Turn the pressure control knob fully counterclockwise to
its lowest pressure setting.
3. Make sure the pump ON/OFF switch is in the OFF
position.
4. Fill the fluid section oil cup with approximately one
tablespoon of piston seal lubricant (Piston Lube).
IMPORTaNT: Never operate unit for more than ten seconds
without fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
5. Check the engine oil level. The gasoline engine oil level
is determined by the manufacturer. Refer to the engine
manufacturer's service manual (supplied).
6. Close the fuel shut-off lever and fill the gas tank with
gasoline. Use only high quality, unleaded gasoline.
One-Gun Setup
1. Using a wrench, thread the 50' airless spray hose to the
outlet fitting on the sprayer. Tighten securely.
2. Attach an airless spray gun to the spray hose. Using two
wrenches (one on the gun and one on the hose), tighten
securely.
Two-Gun Setup
1. Using a wrench, thread the valve assembly (with 50' hose
attached) to the outlet fitting on the sprayer. Tighten
securely.
2. Using a wrench, thread the 6' airless spray hose to the top
outlet fitting on the valve assembly. Tighten securely.
6' hose
Valve
assembly
50' hose
Outlet
fitting
3. Attach an airless spray gun to each of the spray hoses.
Using two wrenches (one on the gun and one on the
hose), tighten securely.
NOTE: If you plan on using both guns, make sure the
valve handle is in the open position (handle is in
line with the 6' hose)
Valve
closed
© Titan Tool Inc. All rights reserved.
Positioning the spray guns (both units)
1. Loosen the support bar knob and slide the gun support bar
to the desired horizontal position. Make sure the gun is far
enough away from the cart so that the rear wheel does not
track over the fresh spray pattern.
2. 2nd Gun Mounting (if equipped) -
a. Slide the 2nd gun support bar assembly over the end of
the 1st gun support bar. Secure in place by tightening
the 2nd gun support bar knob.
b. Loosen the 2nd gun post knob and slide the post to the
desired horizontal position.
c. Run the 2nd gun cable through the block and cable
guides, underneath the frame and back towards the cart
handle. Use the tie wraps to secure the cable to the
frame.
IMPORTaNT: Make sure the cable is not touching the tires
or interfering with the mobility of the cart in any way.
d. Insert the gun cable assembly into the hole of the
control guide until it snaps into place.
e. Attach the hooked end of the cable into the hole of the
lever plate.
NOTE: See the "adjusting the Trigger Tension" section
in order to verify that the cable is installed
properly.
3. Loosen the gun riser clamp(s) and slide the spray gun(s)
to the desired vertical position(s). A distance of 6" from the
tip to the spray surface is a good starting point.
Gun riser
clamps
Knob
2nd gun
support bar
2nd gun
post knob
NOTE: The gun support bar and the spray gun(s) can be
mounted on either side of the sprayer. Refer to
the "Spray Gun Positions" illustration near the
back of this manual.
NOTE: The height of the spray gun affects the width
Valve
of the spray pattern (i.e., the lower the gun, the
open
smaller the line width). Tip size also affects line
width.
5
Gun cable
Lever plate
Control guide
Gun
support
bar
Block
English
Support
bar knob