Table Des Matières - Titan SPEEFLO PowrLiner 2850 Notice D'utilisation

Important Safety Information
6. Do not kink or over-bend the hose. Airless hose can develop
leaks from wear, kinking and abuse. A leak can inject
material into the skin.
7. Do not expose the hose to temperatures or pressures in
excess of those specified by manufacturer.
8. Do not use the hose as a strength member to pull or lift the
equipment.
9. Use lowest possible pressure to flush equipment.
10. Follow all appropriate local, state and national codes
governing ventilation, fire prevention and operation.
11. The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.
12. Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement
of couplings. Immediately replace hose if any of those
conditions exist. Never repair a paint hose. Replace with a
conductive high-pressure hose.
13. Do not spray outdoors on windy days.
14. Always unplug cord from outlet before working on equipment
(electric models only).
IMPORTaNT: Do not lift cart handle when loading or unloading.
Gasoline Engine Safety
The engine exhaust from this unit contains chemicals
known to the State of california to cause cancer, birth
defects, or other reproductive harm.
1. Gas engines are designed to give safe and dependable
service if operated according to instructions. Read and
understand the engine Owner's Manual before operating the
engine. Failure to do so could result in personal injury or
equipment damage.
2. To prevent fire hazards and to provide adequate ventilation,
keep the engine at least 1 meter (3 feet) away from buildings
and other equipment during operation. Do not place
flammable objects close to the engine.
3. Children and pets must be kept away from the area of
operation due to a possibility of burns from hot engine
components or injury from any equipment the engine may be
used to operate.
4. Know how to stop the engine quickly, and understand the
operation of all controls. Never permit anyone to operate the
engine without proper instructions.
5. Gasoline is extremely flammable and is explosive under
certain conditions.
6. Refuel in a well-ventilated area with the engine stopped. Do
not smoke or allow flames or sparks in the refueling area or
where gasoline is stored.
7. Do not overfill the fuel tank. After refueling, make sure the
tank cap is closed properly and securely.
8. Be careful not to spill fuel when refueling. Fuel vapor or
spilled fuel may ignite. If any fuel is spilled, make sure the
area is dry before starting the engine.
9. Never run the engine in an enclosed or confined area.
Exhaust contains poisonous carbon monoxide gas; exposure
may cause loss of consciousness and may lead to death.
10. The muffler becomes very hot during operation and remains
hot for a while after stopping the engine. Be careful not to
touch the muffler while it is hot. To avoid severe burns or fire
hazards, let the engine cool before transporting it or storing it
indoors.
11. Never ship/transport unit with gasoline in the tank.
© Titan Tool Inc. All rights reserved.
operating the equipment. SavE ThESE INSTRucTIONS.
·
Read all safety information before
Specifications
Gallons per minute (GPM) ............. 0.85 (3.22 LPM)
Maximum tip size ........................... 1-Gun - 0.030"
Maximum pressure ........................ 3300 PSI (22.8 MPa)
Power ......................................... 4.3 HP Robin-Subaru gas
Weight ......................................... 138 lbs. (62.6 kg)
Table of contents
Safety Precautions ................................................................... 2
Français............................................................................. 18
Español ............................................................................. 36
General Description ................................................................. 4
Trigger Lock ........................................................................ 4
Operation ................................................................................... 4
Fueling................................................................................. 4
Setup ................................................................................... 5
Preparing a New Sprayer .................................................... 6
Preparing to Paint................................................................ 7
Painting ............................................................................... 7
Operating the Front Caster.................................................. 8
Pressure Relief Procedure .................................................. 8
cleanup ..................................................................................... 8
Cleaning the Spray Tip ........................................................ 9
Maintenance .............................................................................. 9
General Repair and Service Notes...................................... 9
Maintaining the Engine ........................................................ 9
Adjusting the Trigger Tension ............................................. 9
Replacing the PRIME/SPRAY Valve ................................. 10
Cleaning or Replacing the Filters ...................................... 10
Replacing the Pump ON/OFF Switch ................................ 11
Replacing the Gears and/or Slider Assembly............... 11-12
Replacing the Transducer ................................................. 12
Servicing the Clutch Assembly ..................................... 12-14
Servicing the Fluid Section ........................................... 15-16
Troubleshooting ..................................................................... 17
Parts Listings .......................................................................... 48
Main Assembly .................................................................. 48
Drive Assembly ................................................................. 50
Fluid Section Assembly ..................................................... 54
Cart Assembly ................................................................... 56
Front Wheel Assembly ...................................................... 58
Gun Holder Assembly ....................................................... 60
Brake Assembly ................................................................ 60
Accessories ....................................................................... 62
Limited Warranty .................................................................... 64
3
2-Gun - 0.021"
engine
English