Publicité
Les langues disponibles
Les langues disponibles
PIN 1: GND: GROUND
PIN 2: ALARM INPUT 8: By connecting ALARM INPUT 8 (pin 2) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 3: ALARM INPUT 6: By connecting ALARM INPUT 6 (pin 3) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 4: ALARM INPUT 4: By connecting ALARM INPUT 4 (pin 4) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 5: ALARM INPUT 2: By connecting ALARM INPUT 2 (pin 5) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 6: ALARM INPUT 16: By connecting ALARM INPUT 16 (pin 6) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 7: ALARM INPUT 14: By connecting ALARM INPUT 14 (pin 7) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 8: ALARM INPUT 12: By connecting ALARM INPUT 12 (pin 8) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 9: ALARM INPUT 10: By connecting ALARM INPUT 10 (pin 9) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 10: PIN OFF
PIN 11: RS232-TX + PIN 23: RS232-RX: This device can be controlled remotely by an external device or control
system, such as a control keyboard, using RS-232 serial communications signals.
PIN 12: RS485-A + PIN 24: RS485-B: This device can be controlled remotely by an external device or control
system, such as a control keyboard, using RS-485 serial communications signals.
PIN 13: EXTERNAL ALARM NO + PIN 25: EXT. ALARM COM: During normal functioning COM is connected with
NC and not with NO. When there is an alarm trigger, COM disconnects from NC and connects with NO.
PIN 14: PIN OFF
PIN 15: ALARM INPUT 7: By connecting ALARM INPUT 7 (pin 15) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 16: ALARM INPUT 5: By connecting ALARM INPUT 5 (pin 16) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 17: ALARM INPUT 3: By connecting ALARM INPUT 3 (pin 17) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 18: ALARM INPUT 1: By connecting ALARM INPUT 1 (pin 18) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 19: ALARM INPUT 15: By connecting ALARM INPUT 15 (pin 19) to GND (pin 1), the DVR16M will start
recording and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 20: ALARM INPUT 13: By connecting ALARM INPUT 13 (pin 20) to GND (pin 1), the DVR16M will start
recording and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 21: ALARM INPUT 11: By connecting ALARM INPUT 11 (pin 21) to GND (pin 1), the DVR16M will start
recording and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
PIN 22: ALARM INPUT 9: By connecting ALARM INPUT 9 (pin 22) to GND (pin 1), the DVR16M will start recording
and the buzzer will be on. Triggering depends on the set level (high/low) under Menu/Camera/Alarm.
d) Power ON
Before turning power ON make sure any HDD has been locked, and the power LED is red. After pressing the
POWER button, the POWER LED will turn to orange and all the other LEDs will turn RED, except the LED for HDD.
The screen will display "HDD Detecting" ; power on period will be approx. 5 to 15 seconds. If HDD is set as master,
the screen will display " Master HDD Connected". If HDD is set as slave, the screen will display " Slave HDD
Connected". In order to shorten the power on running time, we suggest setting the HDD as master (by means of the
jumper on the HDD itself). When the DVR16M has powered on completely, the POWER LED will turn to green.
DVR16M
- 7 -
VELLEMAN
Publicité
