Telcoma T201 Mode D'emploi page 56

GB
TAB. 2
Function
Step-by-step
input and radio
channel mode
Jolly input mode
Re-closure
Photo test
Release thrust
Slowdown
Closing thrust
Mode
Reclosing after the
photoelectric cells
56
N.
OFF ON
Desciption
Dip
•
1
Open - Stop - Close
•
2
•
1
Open - Close
•
2
•
1
Open
•
Condominium function
2
•
1
Open - Close
•
Cut out of opening control
2
•
3
J1=Open pushbutton
•
J2=Close pushbutton
4
•
3
J1=Opening Edge
J2=Photocell 3
•
4
•
3
2nd pair of limit switches
•
J1=FCA J2=FCC
4
•
3
J1=Clock
•
J2=Photocell 3
4
•
Cut out
5
•
Connected
•
Cut out
6
•
Connected
•
Cut out
•
Connected
•
Cut out
8
•
Connected
•
Cut out
9
•
Connected
•
Cut out
10
•
Connected
Control unit for 1
•
motor or 2 in parallel
11
Control unit for 2
•
independent motors
•
Cut out
12
•
Connected
During opening, upon pressing the P/P button the gate stops, pressing it
again the gate closes. During closing, upon pressing the P/P button the
gate stops, pressing it again the gate opens.
During opening, upon pressing the P/P button the gate stops for a few
seconds and then closes. During closing, upon pressing the P/P button
the gate stops for a few seconds and then opens.
During opening, pressing the P/P button has no effect. During the pause,
pressing the P/P button has no effect. During closing, upon pressing the
P/P button the gate stops for a few seconds and then opens.
During opening, pressing the P/P button has no effect. During the pause,
upon pressing the P/P button the gate closes. During closing, upon pressing
the P/P button the gate stops for a few seconds and then opens.
J1 = opening pushbutton
J2 = closing pushbutton
Use NO contacts or pushbuttons
J1 = "opening edge" input. This safety device is triggered only when the
so it is activated during the closing of the gate. These two safety devices
reverse the moving direction of the gate for a short time.
J2 = input for third photocell; it activates only during an opening manoeuvre
and causes the gate to close. Use N.C. contact.
For installations where 4 limit switches (gate stops) are mounted. Connect
the motor M1 limit switches to the inputs FCC and FCA. Connect the
motor M2 limit switches to the inputs J1 and J2. Use NC contacts.
J1=Clock input; this closes the gate when the contact is opened and
opens it when the contact is closed. J2=input for the third photocell; it only
activates during opening and forces closing. Use NC contacts.
After one complete opening, the control unit only closes again witha manual control.
After one complete opening, the control unit closes automaticallyafter the
programmed pause time.
See text in Fototest section.
See text in Fototest section.
Function cut out.
The release thrust has the function of releasing the electric lock. The leaf
with M1gives a short thrust in the closing direction before starting to open.
There is no slowdown in the last part of travel.
With the slowdown function connected, the motor halves its speedtowards
the end of every gate movement. This function may not workproperly with
hydraulic motors.
No closing thrust is carried out.
The control unit ends gate closure with a short full-power thrust onmotor M1.
The outputs M1 and M2 work in parallel and the pedestrian control
partially opens/closes the gate leaf/s. For single motor control, see the
section "Programming the times".
The outputs M1 and M2 are independent and the pedestrian control
fully opens and closes the leaf with motor M1. For motor control, see the
section "Programming the times".
Function bypassed
The activation of photoelectric cell reduces the pause time for whatever is
value previously was to 2 seconds.
Notes