Publicité
Les langues disponibles
Les langues disponibles
GB
Mor n. Mor n.
1
Motor M1
2
Motor M1
3
Motor M1
2
3
Capacitor
4
Motor M2
5
Motor M2
6
Motor M2
5
6
Capacitor
7
8
Flashing light
9
8
Light
10
11
Line
12
13
Auxiliares
Photocell/s
14
15
transmitter
15
16
Warning light
17
18
Electric lock
20
19 o 25 N.C. contact
21
19 o 25 N.C. contact
22
19 o 25 N.C. contact
23
19 o 25 N.C. contact
19 o 25 N.C. contact or
24
N.O. pushbutton
N.C. contact or
26
25 o 31
N.O. pushbutton
27
25 o 31 N.C. contact
28
25 o 31 N.O. pushbutton
29
25 o 31 N.C. contact
30
25 o 31 N.O. pushbutton
32
Receiver antenna Rx*
33
Receiver antenna Rx*
34
35
Auxiliares
36
Encoder 2
37
Encoder 2
38
Encoder 2
39
Encoder 1
40
Encoder 1
41
Encoder 1
Input
Output
*ANTENNA: pay attention if a plug-in radio card is used, since the connector for antenna connection in certain models is
on the actual card.
Device
V
I max
230Vac
4A
230Vac
4A
230Vac
4A
230Vac
4A
230Vac
4A
230Vac
4A
230Vac
4A
230Vac
4A
230Vac
1A
230Vac
1A
230Vac
6,3A
24Vac
150mA
24Vac
150mA
24Vac
100mA
12Vcc
1A
Max 24V 500mA
0 V
~20V
0 V
~20V
Function
Common M1
Close M1
Open M1
Motor breakaway M1
Common M2
Close M2
Open M2
Motor breakaway M2
Movement indicator
Courtesy light
C. unit power supply
Power supply
Transmitter power supply
for foto-test
Gate open
Mechanical lock
Closing limit switch (M1)
Opening limit switch (M1)
Photocell 1
Photocell 2
Jolly 2
Jolly 1
Fixed safety edge
Pedestrian gate
Stop
Step-by-step
Control unit
Braid
II° Receiver channel
Negative power supply
Positive power supply
Data
Negative power supply
Positive power supply
Data
Notes
The motor M1 is delayed for gate clo-sing.
In swing gate installa-tions the motor M1 should control theleaf with the
electric lock.
See motor notes
The motor M2 is delayed for gateopening (with dip-switch n. 11 set to ON)
See motor notes
On when the motor is working. Switchingon may be anticipated (pre-
blinking), seedipswitch No.5 functions
On, from start of movement to 3minutes after full closure
Connect to the 230Vac line. See"ELECTRICAL CONNECTIONS"
Permanent for photocells and auxilia-ries power supply
Power supply for photocell transmitter (if the Foto test function is used)
Use a 24V 2W max.bulb, see text
Active for a few seconds at everystart of opening
Connect this input if not used to thecommon terminal.
Connect this input if not used to thecommon terminal.
During closure it reverses the direc-tion.
Connect this input if not used tothe common terminal
Temporary stop during opening.
During clo-sing it reverses the direction.
Connect thisinput to the common terminal if it is notused.
See dipswitch No.3 and 4 functions.
If this input is not used, put dipswit-ches 3 and 4 to OFF.
See dipswitch No.3 and 4 functions.
If this input is not used, put dipswit-ches 3 and 4 to OFF.
Reverse the direction for a few seconds andthe control unit locks.
Connect this input tothe common terminal if it is not used.
With 2 motors, opening is carried outby just motor M1.
With 1 motor, ope-ning is for just 6 seconds.
Stop all functions.
Connect this input ifnot used to the common terminal.
See functions dip switches No.1 and No.2
Connect an aerial suited to the receiver model
Only available if a two-channel radiocard is inserted in the pre-installed
See motor instructions
55
Publicité
