Presentation And General Points; General Points; Transport And Packaging; Identification Label - Errebi DAKAR-SMART Notice D'utilisation

ENGLISH
>>>
1

Presentation and general points

The DAKAR-SMART key cutting machine has been desig-
ned taking into account the safety standards currently
in force in the EEC.
The safety of the persons operating this type of machi-
ne can only be guaranteed by means of a correctly-
designed personal safety programme, implementing
a maintenance programme and following the advice
recommended, and compliance with the safety stan-
dards indicated in this manual.
Although machine installation is a simple process, this
manual should be carefully read before installing, adjus-
ting and using it.
The machine leaves our factory ready for use and only
requires calibration of the tools to be used.

1.2 TRANSPORT AND PACKAGING

The DAKAR-SMART machine is supplied in a strong car-
dboard box, protected with packing foam and with the
following dimensions:
Width = 520 mm; Height = 650 mm; Depth = 575 mm
Weight of machine with packaging = 23 Kg.
On unpacking the machine, check whether it has suffe-
red any damage during transportation.
If you should observe any problems, inform the carrier
immediately and do not use the machine until it has
been inspected by the carrier's agent.
To move the machine, we recommend picking it up by
its base only, and not by any other part.
The DAKAR-SMART key cutting machine has an iden-
tification label specifying the serial or registration
number of the machine, the name and address of the
manufacturer, the EC conformity mark and the year of
manufacture.
>>> 8

1.1 GENERAL POINTS

1.3 IDENTIFICATION LABEL

See figure 1
2

Machine characteristics

The DAKAR-SMART machine is an accurate, robust key
cutting machine with an interchangeable clamp ena-
bling duplication of a large range of key types.

2.1 MAIN ELEMENTS OF THE MACHINE

Clamp holder carriage (X- and Y-axes)
1
Head (Z-axis)
2
Clamp
3
Clamp opening/closing knob
4
Clamp holder carriage locking knob (X-axis)
5
6
Head blocking knob (Z-axis)
7 Tracer point locking knob (fixed/springing)
8 Tracer point adjustment wheel
9
Carriage drive lever (X- and Y-axes)
10
Head drive lever (Z-axis)
11
Milling cutter holder head
12 Tracer point holder head
Milling cutter
13
Tracer point
14
15 Master switch
16
Start-up switch
17
Motor switch

2.2 TECHNICAL DATA

Motor: Single phase 200 W, 230 V - 50 Hz; (Optional: Single
phase 200W, 110V – 60Hz)
Milling cutter: High-speed steel (HSS)
Milling cutter speed: 5500 r.p.m.

Clamps:

Interchangeable
Displacement: Guided by ground shafts
Effective travel: X-axis = 32 mm; Y-axis = 40 mm; Z-axis = 27 mm
Dimensions: Height = 378 mm; Width = 270 mm; Depth = 340 mm
Weight: 18 Kg

2.3 COMPONENTS AND FUNCTIONAL PARTS

2.3.1 Electrical circuit

The main components of the electrical and electronic
circuit are as follows:
Mains connection: With fuses and a master
1
switch.
Connection plate: Base for connections.
2
Start-up switch: Visible luminous switch for
3
starting up the machine.
4 2-way switch: Start/stop.
Motor: Single phase brush motor.
5
2.3.2 Clamps
The standard machine is supplied with a universal clamp,
interchangeable with any of the optional clamps, which
are specially designed so that this machine can duplicate
a wider range of key families.

2.3.3 Carriage lock on X-axis

The X-axis lock is used for straight-line milling or pointing,
in the direction of the Y-axis.
To lock and unlock the carriage in this direction, turn the
corresponding knob.
See figure 2
See figure 3
See figure 4