Technical Data; Remaining Hazards - Scheppach HBS300 Traduction Des Instructions D'origine

It is imperative to observe the accident prevention
•
regulations in force in your area as well as all other
generally recognized rules of safety.
Note the information published by your profession-
•
al associations.
• Adjustable protective devices have to be adjusted
as close as possible to the workpiece.
Important! Support long workpieces (e.g. with a
•
roller table) to prevent them sagging at the end
of a cut.
Make sure the blade guard (3) is in its lower posi-
•
tion when the saw is being transported.
• Safety guards are not to be used to move or mis-
use the machine.
Blades that are misshapen or damaged in any way
•
must not be used.
If the table insert is worn, replace it.
•
Never operate the machine if either the door pro-
•
tecting the blade or the detachable safety device
are open.
Ensure that the choice of blade and the selected
•
speed are suitable for the material to be cut.
Do not begin cleaning the blade until it has come
•
to a complete standstill.
For straight cuts of small workpieces against the
•
longitudinal limit stop the push stick has to be
used.
The bandsaw blade guard should be in its lowest
•
position close to the bench during transport.
For miter cuts when the table is tilted, the paral-
•
lel stop must be positioned on the lower part of
the table.
• When cutting round timber, use a suitable holding
device to prevent the workpiece turning.
Never use guards to lift or transport items.
•
Ensure that the bandsaw blade guards are used
•
and correctly adjusted.
Keep your hands a safety distance away from the
•
bandsaw blade. Use a push stick for narrow cuts.
• The push stick has to be stored on the intended de-
vice, so that it can be reached from normal working
position and is always ready to be used.
In the normal operating position the operator is in
•
front of the machine.

6. Technical data

Electro motor
Power
Revolutions
Saw band length
Saw band width
Saw band width max.
Cutting speed
Passage height
Passage width
24 GB
220 - 240 V ~, 50 Hz
750W
1400 min
-1
2240 mm
12,5 mm
15 mm
720 m/min
360 m/min
0 - 175 mm
Table size
Slewing range of the table
Max. size of the workpiece
Overall weight
Gewicht
The work piece must have a minimum height of 3mm
and a minimum width of 10 mm.
The total noise values determined in accordance
with EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.

7. Remaining hazards

The machine has been built using modern technolo-
gy in accordance with recognized safety rules. Some
remaining hazards, however, may still exist.
Risk of injury for fingers and hands by the rotating
•
saw band due to improper handling of the work
piece.
Risk of injury through the hurling work piece due
•
to improper handling, such as working without the
push stick.
Risk of damaging your health due to wood dust and
•
wood chips. Wear personal protective cloth such
as goggles. Use a fitting dust extractor.
• Risk of injury due to defective saw band. Regu-
larely check saw band for such defects.
Risk of injury for fingers and hands while changing
•
saw band. Wear proper gloves.
Risk of injury due to starting saw band while
•
switching on the machine.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
Wear only closefitting clothes. Remove rings,
•
bracelets and other jewelry.
For the safety of long hair, wear a cap or hair net.
•
Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
Remaining hazards can be minimized by follow-
•
ing the instructions in „General safety instructions"
„Proper Use" and in the entire operating manual.
305 mm
500 x 400 mm
0° bis 45°
600 x 600 x 175 mm
74 kg
77,4 dB(A)
3 dB
90,4 dB(A)
3 dB