Remaining Hazards; Machine Specifications; Technical Data; Noise Emission - Jet JBOS-5 Mode D'emploi

Always wear the approved working
outfit.
Do not wear gloves.
Install the machine so that there is
sufficient space for safe operation and
workpiece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled table
surface.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense. Do not operate
the machine when you are tired.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Keep children and visitors a safe
distance from the work area.
Do not operate the electric tool near
inflamm able liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust extraction
device
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Never operate with the table insert not
in place.
Make sure to guide and hold the
workpiece tight during machining.
Machine only stock which rests
securely on the table.
Specifications regarding the maximum
or minimum size of the workpiece
must be observed.
Do not remove chips and workpiece
parts until the machine is at a
standstill.
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
Replace any torn or worn sanding belt
immediately.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist.
The moving sanding sleeve can cause
injury.
Risk of kickback. The workpiece is
caught by the moving sanding sleeve
and thrown back to the operator.
Thrown workpiece parts can lead to
injury.
Sanding dust and noise can be health
hazards. Be sure to wear personal
protection gear such as safety goggles
and dust mask. Use a suitable dust
exhaust system.
Defective sanding discs can cause
injuries.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.

4. Machine specifications

4.1 Technical data

Table size(LxW)
Table tilt
Spindle speed
Oscillations
Oscillation stroke
Sanding sleeve length
Dust port diameter
suction at 20 m/sec
Overall (LxWxH) 370x370x460mm
Net weight
4
Mains
Output power
Reference current
Extension cord (H07RN-F):
Installation fuse protection

4.2 Noise emission

Acoustic pressure level (EN 11202):
Idling
In operation
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
As workplace conditions vary, this
information is intended to allow the
user to make a better estimation of the
hazards and risks involved only.
4.3 Content of delivery
6, 12, 16, 38 and 50mm spindles with
sanding sleeves
2 oblong table inserts
2 round table inserts
Spindle holder
Insert holder
100mm dust port
Operating tools
Assembly kit
Operating manual
Spare parts list.

5. Transport and start up

5.1 Transport and installation

The machine is designed to operate in
closed rooms and must be placed
stable on a firm and levelled table
surface.
For packing reasons the machine is
not completely assembled.

5.2 Assembly

If you notice transport damage while
unpacking, notify your supplier
immediately. Do not operate the
370x370mm
machine!
0 - 45°
Dispose of the packing in an
1400 rpm
environmentally friendly manner.
30/min
25mm
Clean all rust protected surfaces with
a mild solvent.
150mm
Attach the spindle storage shelf (A,
100mm
Fig 1) and the insert storage shelf (B,
560m3/h
Fig 1) to the cabinet using six screws.
30 kg
230V ~1/N/PE 50Hz
0,37 kW (0,5HP) S1
3.6 A
3x1,5²
10A
69,4 dB (A)
78,5 dB (A)