Before Proceeding; How To Use This Manual - Pioneer PDP-505HD Mode D'emploi

B P
EFORE ROCEEDING
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

How to use this manual

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
This manual is set up to follow the course of actions and
operations in the order that would seem most logical for
someone setting up this unit.
Once the unit has been taken out of the box, and it has
been confirmed that all the parts have been received, it
may be beneficial to look over the section "Part Names
and Functions" starting on page 6 to become acquainted
with the plasma monitor and remote control unit, as their
respective buttons and controls will be referred to
throughout this manual. For descriptions of the remote
control unit buttons used to control other components in
your system, refer to the section "Operating Other
Devices" starting on page 39.
The section "Installation and Connections" starting on
page 9 covers all the necessary points regarding
installation of the plasma display and connections to a
wide variety of components.
The section "Setting Up the System" starting on page 17
covers the necessary on-screen menu settings to
establish correct linkage between the plasma display and
connected components. Depending on the connections
made, this section may or not be necessary.
The section "Operations" starting on page 20 covers the
basic procedures used to operate the plasma display.
The section "Display Panel Adjustments" starting on
page 28 describes how to use the on-screen menus to
make picture quality and screen adjustments.
About operations in this manual
Operations in this manual are outlined in step by step
numbered procedures. Most of the procedures are
written in reference to the remote control unit unless the
button or control is only present on the main unit.
However, if a button or control on the main unit has the
same or similar name as that on the remote control unit,
that button can be used when performing operations.
When using the remote control unit to operate the main
unit or to navigate on-screen menus in the procedures
prior to page 38, be sure the mode switch is set to
"TV/VCR".
The following example is an actual operation that shows
how one might adjust the contrast of the picture. The
screens shown at each step are provided as a visual
guide to confirm that the procedure is proceeding as it
should. Please familiarize yourself with this process
before continuing on with the rest of this manual.
Example) To adjust the contrast of the picture.
CH
MUTING
RECEIVER
1,6
EDIT/
TV/SAT/DTV/DVD
LEARN MENU
SOURCE
%
POWER
2,3,5
SET/
SELECT
DVD
TOP MENU
%
MENU
FAVORITES
1 7
VCR REC
8 ¶ 4
CU-PDP008
PLASMA DISPLAY REMOTE CONTROL UNIT
1
Press MENU to display the menu screen.
The menu screen appears.
PICTURE
SCREEN
SET UP
USE:
END: MENU
2
Press 5/∞ to select PICTURE, then press
SET/SELECT.
The PICTURE adjustment menu screen appears.
PICTURE
MO D E : S T D
C O N T R A S T
B L A C K L V L .
C O L O R
T I N T
S H A R P
O T H E R
E X I T
USE:
VOL
SAT/DTV
GUIDE
2,3,4
(SAT)/DTV
INFO
3 ¡
¢
Î
.
END: MENU
(continued)
3
<ARE1349> En