Pioneer PDP-505HD Mode D'emploi page 43

O O
PERATING THER
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Remote code set up
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
To operate other manufacturers' audio/video components
using the remote control unit supplied with the plasma
display panel, remote control signals need to be set.
There are two methods of setting remote control signals.
÷ Programming the other manufacturers' remote control
signal presets into this remote control unit.
÷ Learning other manufacturers' remote control signals
directly from the remote control units of the other
components.
Programming other
manufacturers' remote control
signal presets
LED indicator
TV CBL
/VCR
/SAT
STANDBY/ON
1 2
SCREEN
MODE AUTO
POWER INPUT
AUDIO CC
1
4
7
¶
RETURN
CH
MUTING
EDIT/ TV/SAT/DTV/DVD
2
LEARN
SOURCE
POWER
SELECT
DVD
TOP MENU
MENU
FAVORITES
1 7
¶
8
CU-PDP008
PLASMA DISPLAY REMOTE CONTROL UNIT
1
Set the mode switch to match the device to which
you want to preset the remote control signal.
Ex) To select DVD/LD, move the switch to the fourth
position as shown below.
TV CBL DTV DVD
/VCR /SAT
D
EVICES
1
DTV DVD
/LD
INPUT
3 4
STILL DISPLAY
RECEIVER DTV
VIEW
CLEAR MODE
2 3
5 6 2,3
8 9
0 CH
ENTER
CH
VOL
RECEIVER
MENU
SAT/DTV
%
GUIDE
SET/
(SAT) /DTV
%
INFO
3 ¡
VCR REC
4 ¢
Î
/LD
2
Simultaneously press EDIT and the number
button "1".
The LED indicator starts blinking.
3
Select the desired manufacturer.
Select from the table on the following page.
Ex) To select a PHILIPS LD player, press the number
buttons "2" and "4" in succession to enter the
number 24.
÷ If the LED indicator blinks rapidly when the number
buttons are pressed, there has been an error. Input
the number again.
÷ After setting, you can automatically use the remote
control in the usual manner.
Notes
÷ To exit the EDIT mode during this operation, press EDIT again.
÷ If the mode switch position is changed while in EDIT mode,
EDIT mode is canceled.
÷ After step 1 and step 2, if you do not press any buttons for
one minute (no operation), the EDIT mode is canceled.
÷ When programming remote control signal presets, make sure
that the learn setting has been reset (page 41).
÷ If the table on the following page does not include the
manufacturer of your component, or the remote control does
not work even after the correct code is entered, you can have
the remote control unit learn its signal using the LEARN mode
of the remote control unit outlined on page 41.
÷ The default setting is "00" for all mode switch settings.
39
<ARE1349> En