NovoPress ACO103 BT Manuel D'utilisation page 21

Pos : 49 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Kapitel übeers chrift+Ü berschrift - T abelle @ 0\mod_1385652188500_18.doc x @ 1618 @ 2 @ 1
8.2 Meaning of the LED display
LED display
Pos : 50 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Alle_LEDs _aus- Kapitel 7.6 @ 5\mod_1522069006044_18.doc x @ 37474 @ @ 1
All LEDs off.
Pos : 51 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _l euc htet @ 0\mod_1400057953215_18.doc x @ 2330 @ @ 1
Green LED (2) lights up.
Pos : 52 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _aus @ 0\mod_1400062238490_18.doc x @ 2344 @ @ 1
Green LED (2) off
(pressing operation in
progress).
Pos : 53 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _blinkt @ 0\mod_1400062218616_18.doc x @ 2337 @ @ 1
Green LED (2) flashes.
Pos : 54 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _blinkt_H altebolz en @ 1\mod_1424269983063_18.doc x @ 9209 @ @ 1
Green LED (2) flashes.
Pos : 55 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _blinkt_H altebolz en_2 @ 1\mod_1424270236239_18.doc x @ 9227 @ @ 1
Green LED flashes.
(Press device
automatically returns to
initial position.)
Pos : 56 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED s (4) @ 0\mod_1400077557059_18.doc x @ 2379 @ @ 1
Green LEDs (4)
Pos : 57 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Bl aue_LED_blinkt @ 3\mod_1491998145093_18.doc x @ 29107 @ @ 1
Blue LED (10) flashes.
Pos : 58 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Bl aue_LED_l euchtet @ 3\mod_1492000411326_18.doc x @ 29128 @ @ 1
Blue LED (10) lights up.
Pos : 59 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/R ote_LED _bli nkt @ 3\mod_1489564282895_18.doc x @ 28653 @ @ 1
Red LED (3) flashes.
Pos : 62 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/R ote_LED _leuchtet @ 0\mod_1400062249067_18.doc x @ 2358 @ @ 1
Red LED (3) lights up.
Pos : 65 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/R ote-und_Grüne_LED _blinken_abwec hs elnd @ 0\mod_1400062253497_18.doc x @ 2365 @ @ 1
Red (3) and green (2)
LED flash alternately.
Pos : 66 /RVT/Allgemeines /#### Seitenumbr uch #### @ 0\mod_1380200837280_0.doc x @ 885 @ @ 1
Status/cause
The device is switched off.
On standby.
Automatic press cycle is on,
device ends the pressing
operation automatically.
Insufficient battery charge.
Retaining pin not correctly
shut.
Retaining pin has come
loose!
Battery charge display
The press device is ready
for connection.
The press device is
connected with the
NovoCheck app.
Device not within the
temperature range
Device fault.
Service interval reached.
17
Measure
Briefly press the start button (1) (see
section 7.6).
Charge or replace battery.
Insert retaining pin, or check retaining pin
and cylinder.
Insert retaining pin, or check retaining pin
and cylinder.
NOTE
The pressing operation may not have
been completed; please check and repeat
if necessary.
The press device can be connected with
the NovoCheck app.
The device only works within a
temperature range of -10 to +50°C. If the
red LED is flashing, the device must be
moved into a warmer or colder area. The
device can be warmed to operating
temperature by means of dry runs.
If the device is too warm it must be cooled
down by means of a short break.
Press the start button (1). If this is
unsuccessful, the press device is
defective.
Send the device to a specialist workshop.
NOTE!
The pressing operation may not have
been completed; please check and repeat
if required.
Take the press device to be serviced.
ACO103 BT
EN