Gaggenau AC230101 Manuel D'utilisation Et Notice D'installation page 28

en Basic operation
7.5 Switching off intensive mode
To select a fan setting of your choice, press
▶
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.6 Switch on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press ⁠ .
▶
a In the LED display, LED 6 lights up for automatic
mode.
7.7 Switch off automatic mode
Press ⁠ .
▶
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
7.8 Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note: This function is only available via a mobile device
with the Home Connect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
7.9 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Default setting: Fan setting 3
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
7.10 Setting the sensor control
Requirement: The appliance is switched off.
Press and hold and for approx. three seconds.
1.
Press or to change the setting.
2.
To cancel the setting, press ⁠ .
3. To save the setting, press and hold
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
1
Depending on the appliance specifications
28
⁠ .
1
1
and for ap-
7.11 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
¡ A repeated signal tone sounds.
Press .
▶
a The saturation indicator is reset.
7.12 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
Press and hold and
1.
To set circulating-air mode (non-regenerable fil-
‒
ter), press ⁠ /
display.
To set circulating-air mode (non-regenerable fil-
‒
ter), press ⁠ /
display.
To convert the electronic control back to opera-
‒
tion without the air recirculation filter, press
until LED 1 lights up on the LED display.
To save the setting, press and hold and for ap-
2.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press ⁠ .
a A signal tone sounds as soon as the selected set-
ting is saved.
7.13 Switching on the button tone
The button tones can be switched on.
Requirement: The appliance is switched off.
Press and hold and
1.
a In the LED display, the LED for the setting that is
currently selected lights up.
Press or until LED 1 lights up in the LED dis-
2.
play.
To cancel the setting, press ⁠ .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.14 Switching the button tone off
The button tones can be switched off.
Note: Signal tones for the appliance are always
switched on and cannot be switched off.
Requirement: The appliance is switched off.
Press and hold and
1.
a In the LED display, the LED for the setting that is
currently selected lights up.
for approx. three seconds.
until LED 2 lights up in the LED
until LED 3 lights up in the LED
for approx. three seconds.
and
for approx. three seconds.
⁠ /
for ap-