Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
8 .5 Memory
Every screw action is stored in the memory according to an
identification number (ID) specifying the date, time, duration of
the screw action, target values programmed (with workflow and
parameter number where applicable), actual values tightened to
and the validation. The basic version has 200 memory locations
and the TOP version has 2000 memory locations.
NOTE! (TOP version only): If you work with workflows
and parameters or the torque check or rotation angle
functions, each memory location has 2 pages that can be dis-
played with
.
NOTICE! The storage symbol on the display denotes
the storage capacity. If all memory locations are full,
the following is displayed along with a yellow light signal:
memory full – data is lost from the next measurement!
This means the next measurement performed is not displayed,
validated or stored in memory. If you confirm this message by
pressing
and
simultaneously, the first 100 of 200 data
records stored (on the basic version) or 125 of 2000 (on the TOP
version) are deleted from the memory. The same message is
displayed as soon as the memory is full again.
The "Memory" menu option enables the data records in the
memory to be displayed and (on the TOP version) deleted indi-
vidually or to be deleted altogether.
1. To access the "Memory" menu option, press
menu.
2. Keep pressing
until you can access the "Memory"
menu option.
3. Pressing
accesses the "Display values" menu option
on the basic version and also the "Delete values" and
"Delete all" menu options on the TOP version. Use
to select the required menu option. The menu option
selected is shown with a black background.
4. Pressing
accesses the menu options selected.
5. "Display values": displays stored data records starting
with the value last stored. You can use the identification
number, the date and time to assign the data stored to
your screw action. Pressing
the data for individual screw actions.
NOTICE! If no data is stored in the memory, "Memory
empty" appears. Confirm by pressing
return to the menu
The following points (6 to 9) only apply to the TOP version:
6. "Delete values": individual data records (IDs) can be
deleted in this menu option.
7. Press
and then use
want to delete. Confirm the selected ID with
"Delete values" appears.
8. Press
to delete the selected ID.
9. "Delete all": this menu option allows you to delete the
entire memory contents. After confirming with
all" is displayed again so the user can be absolutely
sure of the deletion. The entire memory contents are not
deleted until
is pressed again. "Please wait" is dis-
played and then "All deleted". Press
"Memory" menu option.
Design and function
for the
enables you to retrieve
. Use
to
to select the IDs that you
and
, "Delete
to return to the
8 .6 Entering / changing the code
The menu and the settings of the torque wrench with built-in
angle gauge can be blocked to prevent unintentional adjustment
and undesired manipulation of programmes. A code is required
to block and unblock the menu.
NOTICE! The factory set code is "0000".
Select your own 4-digit code.
ATTENTION! Make a note of your new 4-digit code
and have it available when required. If you lose your
4-digit code, please contact your HAZET partner quot-
ing
the
torque wrench with built-in angle gauge.
10. Press
to access the menu.
11. Keep pressing
until you can access the "Code" menu
option.
12. Press
for the "Code" menu option setting range.
13. "Old, 0000" is displayed. The first digit is highlighted.
14. You must enter the old code before entering a new code.
You can change the highlighted code digit with
. Confirm the entry with
lighted. Change the other highlighted digits the same way,
by pressing
and confirming with
NOTICE! When entering your new code for the very first
time, confirm the factory setting of "Old 0000" by
pressing
four times. The positions are highlighted
digit by digit.
15. "New, 0000" is displayed. The first digit is highlighted.
16. Enter your new code by changing the highlighted digits
(by pressing
and confirming with
17. After the last confirmation with
displayed. The new code is stored.
8 .7 Blocking menu access:
18. Press
to access the menu.
19. Keep pressing
until you can access the "Menu
access" menu option.
20. Press
. "Block" is displayed.
21. Press
. "Code, 0000" is displayed. The first digit is
highlighted.
22. Enter the code by changing the highlighted code digits
with
. Confirm the entry with
highlighted. Change the other highlighted digits the same
way, by pressing
23. After the last confirmation with
Block.
24. Pressing
once returns you to the "Menu access"
menu option.
NOTICE! Pressing
ther settings can be changed or configured. The start
display is shown.
25.
You can now only work with the settings
programmed, and can only switch the torque wrench with
built-in angle gauge on and off and re-enable access to
the menu with the appropriate code.
serial
number
of
, then the next digit is high-
.
.
, menu option "Code" is
. The next digit is
and confirming with
.
, you return to display:
again blocks the menu. No fur-
the
29
Publicité
Table des Matières
