Switching On And Off; Menu Access; Inserting Or Replacing Batteries - Hazet-Werk SYSTEM 7000 eTAC Notice D'utilisation

6 . Before starting the operation:
Always ensure tools are used, inspected and main-
tained in compliance with the respective local,
state, national or federal regulations.
To prevent failures in the transfer of force, do not
use hinged joints or extensions if at all possible. The torque
applied to the screw joint can change dramatically when using
hinged joints.
Ensure that the plug tools, socket wrench inserts or other acces-
sories are seated firmly. When using reversible ratchets, check
the required direction of rotation setting. The lever at the top of the
insert reversible ratchet switches the ratchet between clockwise
and anti-clockwise operation.
When using inserts, ensure that their design conforms to stand-
ards and that their shape and size are correct for screw joint con-
nection. You should also ensure compliance with the maximum
permitted load for the insert in use. This can be lower than the
achievable torque for the torque wrench with built-in angle gauge.
Modified or custom-made tools can be dangerous and may not
be used. Do not use worn or damaged tools or inserts. Failure
to comply can result in personal injury and/or material damage.
Position the tool so that it cannot slip from the screw joint. Users
must maintain a safe, balanced position when working. Failure to
do so poses a hazard to persons and a risk of material damage.
It is possible for screw joints to become loose. Do not exceed the
maximum torque of the torque wrench with built-in angle gauge
(such as when undoing bolts which are seized due to rust) under
any circumstances. Overloading may damage the torque wrench
with built-in angle gauge and falsify the release value.
When tightening the rotation angle, ensure that the expected
torque for the set rotation angle does not exceed the maximum
permitted torque for the tool.
7 . Operation:

7.1 Inserting or replacing batteries:

1. Open the screw cap on the end of the handle.
2. Remove the plastic sleeve (with or without the discharged
batteries) from the main tube.
3. Place the batteries required into the plastic sleeve.
NOTICE! The battery symbol on the display
indicates the current battery charge level.
"Flat battery" is displayed if the batteries are dis-
charged. No further work is possible until you change
the batteries. When replacing batteries, push them
out of the sleeve with the new batteries.
ATTENTION! Ensure that all the new bat-
teries are inserted into the sleeve in the
same direction. Only replace the batteries
as a set. Only use the same type of battery.
The batteries included in delivery are not recharge-
able!
4. Insert the sleeve along with the batteries into the main
tube (positive terminal first).
5. Gently tighten the screw cap on the end of the handle by
hand.

Design and function
7 .2 Settings

7.2.1 Switching on and off

Ensure that the torque wrench with built-in angle gauge is not
under load when switched on.
Press
wrench is switched on.
Press
wrench is switched off.
The display shows the factory settings, battery charge state and
the memory display when the wrench is switched on for the first
time.
tion of operation).

7.2.2 Menu access

You can always access the menu with
select individual menu options with
select menu sub-options or configure settings, depending on
the menu option. These must be confirmed with
several times if necessary, to exit the menu/menu options
7.2.3 Language
The "Languages" menu option enables you to set the menu
language (as described in 7.2.2) required for configuring the
wrench settings.
NOTICE! The torque wrench with built-in angle gauge
saves date/time settings for a maximum of 24 hours
without being connected to a power supply.
and at the same time and release – the
and at the same time and release – the
NOTICE! If "System test not OK" or "Service" is dis-
played, please refer to pages 17/18 in the "Faults" sec-
tion
NOTICE! Simultaneously pressing
display (in order to read the display regardless of direc-
rotates the
. From there, you can
. You can then either
. Press ,
25