Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1 . Technical data / tool components:
Technical Specification
HAZET No.
Torque display range (Nm):
Torque measuring range (Nm):
Measuring units
Measuring accuracy, torque range
Adjustable tolerance range for torque
Measurement range for rotation angle
(cumulative)
Measuring accuracy, rotation angle
Adjustable tolerance range for rotation
angle
Insert square (mm)
Calibrated with insert tool
effective length (Wl)/gauge dimension
l
(mm):
w
Length with/without insert tool (mm):
Weight with/without insert tool (kg):
Memory capacity (incl. date and time):
Possibility to program flow charts and
sets of parameters:
Mini-USB port (5-pin)
Menu languages:
Protection rating:
Batteries:
2 . Included in delivery:
• Torque wrench with built-in angle gauge with operating
instructions, examination certificate and batteries in tool
box, insert reversible ratchets according to the table men-
tioned above.
3 . Function / signal levels
• The torque wrench with built-in angle gauge has 4 signal
levels (combined visual, audible and physical signals) that are
activated when configured values are reached.
• The visible signals are shown below the matted ring on the
handle, the audible signals are generated by a buzzer in the
housing and the physical signals are created by a vibration
motor in the handle.
• The torque wrench with built-in angle gauge has two
selectable operating modes: "Torque" and "Rotation angle".
Design and function
Basic version
7290-1 eTAC 7291-1 eTAC 7292-1 eTAC 7294-1 eTAC 7290-2 eTAC 7291-2 eTA 7292-2 eTAC 7294-2 eTAC
1.5 – 60
5 – 100
10 – 200
3 – 60
10 – 100
20 – 200
Nm and lbf.ft
± 2 % / ± 1 digit
± 2 % / ± 1°
9 x 12
6402-1 2
6404-1 3
30
389 / 344 425.5 / 380.5 580 / 518 1018.5 / 942.5 389 / 344 425.5 / 380.5 580 / 518 1018.5 / 942.5
0.82 / 0.73
0.87 / 0.78
1.25 / 0.98
up to 200 measurings
–
–
German and English
4 x 1.5 volt AA (Mignon) or 4 x 1.2 volt AA Mignon
20 – 400
1.5 – 60
40 – 400
3 – 60
± 1 % to ±10 %
1° to 999°
± 1° to ± 90°
14 x 18
6406 4
38.5
44
3.2 / 2.3
0.82 / 0.73
IP 40
• In "Torque" mode, you can select the torque programmes
"Torque track" and "Torque peak".
• A snug torque (starting point for the angle measurement), a
target value for the rotation angle and a +/- tolerance for the
rotation angle in "°" (degrees) are entered in the "Rotation
angle" programme.
• Yellow light flashes once on reaching the snug torque and
therefore the start of angle measurement.
• The first signal level – yellow flashing light, acoustic signal
and low-frequency vibration – starts when the applied
torque reaches the set threshold value of 80% of the lower
value of the target value range. Once the first signal level
is reached, you should reduce the tightening speed and
pay closer attention to the force you are applying, the
display and the signals of the torque wrench with built-in
angle gauge. The lower the target value and the higher
the threshold, the quicker the first signal level is exceeded.
TOP version
5 – 100
10 – 200
10 – 100
20 – 200
Nm, lbf.ft, lbf.in and kfg.m
± 1 % / ± 1 digit
± 1 % / ± 1°
9 x 12
14 x 18
6402-1 2
6404-1 3
30
38.5
0.87 / 0.78
1.25 / 0.98
up to 2000 measurings
10 / 10
v
German and English
further languages on request
20 – 400
40 – 400
6406 4
44
3.2 / 2.3
21
Publicité
Table des Matières
