Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
8 .3 Parameters / workflow
(TOP version only)
The "Parameters" menu option enables the appropriate
programmes to be stored for up to 10 different screw
actions. Up to 10 parameters can be stored in up to 10
workflows each in any order (and with repetitions) in the
"Workflow" menu option. A workflow can also be made
up of just one parameter. Activating a workflow enables
these screw actions to be completed one after another.
The workflow activated, the current position in the workflow
and which parameter can be processed next appear on the
wrench display.
Programming parameters:
1. You must switch to the menu with
"Parameters" menu option with
eters.
2. After pressing
can select the required parameter – from "Parameter 1"
to "Parameter 10" – with
within the parameter selection.
3. Confirming the parameter selected with
"Inactive" / "Active".
NOTICE! If the
ground, this parameter is not currently being used in
a workflow. If the
"Active"
this parameter is being used in at least one workflow. Check
carefully whether you really want to change this parameter
because the change becomes effective when a workflow
containing this parameter is activated.
4. If you want to change the parameter, press
"Torque" / "Rotation angle". Here you can use
select the mode in which this parameter is programmed.
The mode selected is shown with a black background.
5. See page 12 (under Torque) for the programming mode
"Torque": from 8.1
6. See page 12 (under Rotation angle) for the programming
mode "Rotation angle": from 8.2
Activating workflow:
7. You must activate the parameter(s) via a workflow to work
with one or more programmed parameters.
8. Use
to switch to the menu and select the "Workflow"
menu option with
9. After pressing
select the required workflow (from 1 to 10) with
to go backwards within the workflow selection.
10. Confirming the workflow selected with
"Inactive" / "Active". If the "Inactive" display is shown with
a black background, the workflow is not activated. If the
"Active" display is shown with a black background, the
workflow is already activated.
11.
is used to set an inactive workflow to "Active" and
to set an active workflow to "Inactive".
28
Design and function
and select the
to program param-
in the "Parameters" menu option, you
. Use
to go backwards
"Inactive"
display has a black back-
display has a black background,
.
in the "Workflow" menu option, you can
12. If the "Inactive" display is shown with a black background,
pressing
display has a black background, pressing
required parameters in this workflow.
13. The 1st parameter (P) in the 1st step of a workflow (e.g.
A 1.1) has a black background. Pressing
required parameter to be selected, counting upwards
from Parameter 1 to Parameter 10. Use
wards within the parameter selection.
NOTICE! Select the parameters for your workflow once
they have been checked for correct programming.
14.
step of a workflow, press
for the 2nd step of this workflow with a black background
(this can be selected as described above).
15. Press
"Workflow" menu option.
16. If you want to work directly with this workflow, press
again to show the start display with the workflow. After
pressing
ready to use and the workflow can be completed.
displays
17. If you do not want to work directly with this workflow yet,
select the "Workflow"
flow to "Inactive", as described in 5 and 6.
8 .4 Signals
The Signals menu option allows you to set the threshold, to
enable/disable the buzzer and to enable/disable vibration. The
threshold defines when the 1st signal level is to be activated. This
value (as a percentage) is relative to the lower value of the target
value range. To access the Signals menu option, press
to display
for the menu.
to
18. Keep pressing
menu option.
19. Press
20. The Threshold menu option enables you to set the thresh-
old to the required value (with
NOTICE! The range for the threshold is 50% to 99%.
The higher the threshold is set, the quicker the 1st signal
level is exceeded.
21. Confirm the entered value with
22. The next menu level allows you to enable/disable the
buzzer. Select the required setting using
selected setting is shown with a black background.
Confirm the required setting with
23. The next menu level allows you to enable/disable vibra-
. Use
tion. Select the required setting using
setting is shown with a black background. Confirm the
displays
required setting with
takes you back to the menu. If the "Active"
After selecting a parameter for the 1st
– this shows the parameter
to end workflow programming. You return to the
"OK" is no longer displayed, the wrench is
menu option and set this work-
(TOP version only)
until you can access the "Signals"
for the signals setting range.
.
.
includes the
enables the
to go back-
:
).
. The
.
. The selected
Publicité
Table des Matières
