Technical Data; Noise Information; Declaration Of Conformity - Bosch GAS 55 M AFC Professional Notice Originale

OBJ_BUCH-1747-001.book Page 20 Friday, February 15, 2013 8:02 AM
20 | English
19 Castor frame
20 Locking latch of filter cover
21 Holder for crevice nozzle/elbow
22 Holder for vacuum tubes
23 Drain hose
24 Holder for floor nozzle
25 Tool sleeve
26 Air diffuser
27 Vacuum hose
28 Elbow
29 Disposal bag
30 Flat-fold filter(PES)
31 Crevice nozzle
32 Rubber lip
33 Brush insert
34 Floor nozzle
35 Vacuum tube
36 Retainer for vacuum-hose holder
37 Snap-fastener
38 Signalling LED
39 Filter cover
40 Level sensors
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.

Technical Data

Wet/dry vacuum cleaner
Article number
Rated power input
Frequency
Container volume (gross)
Net volume (for fluids)
Dust bag contents
Max. vacuum*
– Vacuum cleaner
– Turbine
Max. flow rate*
– Vacuum cleaner
– Turbine
Max. vacuum capacity
Surface of flat-fold filter
Dust category
Weight according to
EPTA-Procedure 01/2003
Protection class
Degree of protection
Ø
* Measured with a 35 mm and 5 m long vacuum hose
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
1 619 929 L62 | (15.2.13)
Automatic Start/Stop feature*
EU
UK
UK/DK
CH
* Specification of the allowable load of the connected power tool (coun-
try-specific)

Noise Information

Measured sound values determined according to EN 60704.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
GAS 55 M AFC
3 601 JC3 3..
W 1200
Robert Bosch GmbH, Power Tools Division
Hz 50/60
D-70745 Leinfelden-Echterdingen
l 55
15.02.2013
l 40
Assembly
l 27
 Before any work on the vacuum cleaner itself, pull the
230
hPa
mains plug.
hPa 254
Mounting the Vacuum-hose Holder (see figure A)
36
l/s
– Slide the vacuum-hose holders 4 firmly from above into the
l/s 74
retainers 36 intended for this purpose, until they engage.
W 1380
Mounting the Vacuum Hose (see figure B)
2
m 0.615
– Mount the vacuum hose 27 onto the hose connection
M
piece 3 and turn it in clockwise direction to the stop.
Note: While vacuuming, an electrostatic charge develops in
kg 16.2
the vacuum hose and accessories caused through the friction
/I
of the dust, which the operator could experience in the form
of static discharging (dependent on environmental influences
IP X4
and physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory), when vacuuming fine dusts and dry
materials.
max. power
Rated voltage output
220 –240 V 2200 W
110 V 750 W
240/230 V 1800 W
230 V 1100 W
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools
min. power
output
100 W
100 W
100 W
100 W