Specifications - Sony XM-GS6DSP Mode D'emploi

Specifications

AUDIO POWER SPECIFICATIONS
CTA2006 Standard
Power Output: 45 Watts RMS × 4 at 4
Ohms, 90 Watts RMS × 2 at 4 Ohms < 1%
THD+N
SN Ratio: 83 dBA (FRONT/REAR), 80 dBA
(SUB) (reference: 1 Watt into 4 Ohms)
Wireless Communication
Communication System:
BLUETOOTH Standard version 3.0
Output:
BLUETOOTH Standard Power Class 2 
(Max. Conducted +1 dBm)
Maximum communication range*
Line of sight approx. 10 m (33 ft)
Frequency band:
2.4 GHz band 
(2.4000 GHz – 2.4835 GHz)
Modulation method: FHSS
Compatible BLUETOOTH Profiles*
A2DP (Advanced Audio Distribution Profile) 1.3
AVRCP (Audio Video Remote Control Profile) 1.5
SPP (Serial Port Profile)
Corresponding codec:
SBC (.sbc), AAC (.m4a)
*1 The actual range will vary depending on factors such
as obstacles between devices, magnetic fields
around a microwave oven, static electricity,
reception sensitivity, antenna (aerial)'s performance,
operating system, software application, etc.
*2 BLUETOOTH standard profiles indicate the purpose
of BLUETOOTH communication between devices.
General
Circuit system: 
Class D Amplifier,
Pulse power supply
Inputs: 
RCA pin jacks,
High level input connector
Input level adjustment range (in 6ch mode):
0.3 V – 6 V (RCA pin jacks),
3 V – 12 V (High level input)
Outputs: 
Speaker output connector,
WOOFER/SUBWOOFER terminals
Speaker impedance: 
4 Ω – 8 Ω (Speaker output connector),
2 Ω – 8 Ω (WOOFER/SUBWOOFER terminals)
20
GB
1 :
2 :
Maximum output: 
5 Speakers:
100 W × 4 (FRONT/REAR at 4 Ω),
1,100 W × 1 (SUB BTL at 2 Ω)
6 Speakers:
100 W × 4 (FRONT/REAR at 4 Ω),
300 W × 2 (SUB at 2 Ω)
Rated output (supply voltage at 14.4 V, 20 Hz –
20 kHz, 1% THD):
6 Speakers:
45 W × 4 (FRONT/REAR at 4 Ω),
90 W × 2 (SUB at 4 Ω)
Frequency response:
+0.5
20 Hz – 20 kHz (
−3.0
+0.5
20 Hz – 10 kHz (
−3.0
Harmonic distortion: 
0.1% at 1 W, 1 kHz (FRONT/REAR at 4 Ω),
0.1% at 45 W, 1 kHz (SUB at 4 Ω)
Low-pass filter: 
500 Hz – 4 kHz, 12 dB/oct (REAR),
50 Hz – 500 Hz, 12 dB/oct (SUB)
High-pass filter: 
500 Hz – 4 kHz, 12 dB/oct (FRONT),
50 Hz – 500 Hz, 12 dB/oct (REAR)
Low boost: 
0 dB – 10 dB (40 Hz) (SUB)
Power requirements: 
12 V DC car battery (negative ground (earth))
Power supply voltage: 
10.5 V – 16 V
Current drain: 
At rated output: 36 A
45 W × 4 (FRONT/REAR at 4 Ω),
90 W × 2 (SUB at 4 Ω)
ACC Input: 1 mA
Remote input: 1 mA
Dimensions: 
Approx. 295 mm × 51 mm × 199.5 mm 
(11 / × 2 / in × 7
5 1
8 in 8
projecting parts and controls
 295 mm (11
5 / in)
8
 248 mm (9
7 / in)
8
 184.8 mm (7
3 /
8
 199.5 mm (7
7 / in)
8
 51 mm (2
1 / in)
8
dB) (FRONT/REAR),
dB) (SUB)
/ in) (w/h/d) not incl.
7
8
in)