Specifications - Sony TA-VE910 Mode D'emploi

Specifications

Amplifier section
POWER OUTPUT
Stereo mode
(8 ohms 20 Hz - 20 kHz, THD 0.09%)
100 W + 100 W
Surround mode (8 ohms at 1 kHz, THD 0.8%)
Front: 100 W/ch
*
Center : 100 W
*
Rear : 100 W/ch
*
Depending on the sound field settings and the
source, sound will not be output.
Dynamic power output
155 W + 155 W, 8 ohms
220 W + 220 W, 4 ohms
Harmonic distortion at rated output
Less than 0.09% (with DIRECT PASS on)
Frequency response
PHONO: RIAA equalization curve
±0.5 dB
CD, TAPE, DAT/MD, VIDEO 1, 2:
+0
10 Hz - 50 kHz
–1
Inputs
Sensitivity
PHONO
2.5 mV
CD, TAPE, DAT/MD,
TUNER, VIDEO 1, 2, 3,
150 mV
LD, TV
—
LD AC-3 RF
LD, CD, DAT/MD
—
OPTICAL
LD COAXIAL
—
**
'78 IHF
Outputs VIDEO 1, 2 AUDIO OUT:
Voltage: 150 mV, Impedance: 10 kilohms
WOOFER:
Voltage: 2 V
Impedance: 1 kilohms
PHONES:
Accepts low and high impedance headphones
BASS BOOST +6 dB at 50 Hz
dB (with DIRECT PASS on)
S/N (weighting
network, input
Impedance
level)
**
75 dB
50 kilohms
(A, 2.5 mV)
**
82 dB
50 kilohms
(A, 150 mV)
100 dB
75 Ω
(A, 20 kHz LPF)
100 dB
—
(A, 20 kHz LPF)
100 dB
75 Ω
(A, 20 kHz LPF)
Additional Information
Digital signal processor section
Modulation (A/D conversion)
High Density Linear Converter
Demodulation (D/A conversion)
High Density Linear Converter
(Advanced pulse D/A converter)
Sampling frequency
48 kHz
Surround LFE MIX: MUTE, –20 - 0 dB, 0.5 dB step
D. RANGE COMP: OFF, 0.1 - 0.9, STD, MAX
REAR level: –20 - +10 dB, 0.5 dB step
CENTER level: –20 - +10 dB, 0.5 dB step
SUB WOOFER level: –20 - +10 dB, 0.5 dB step
EFFECT: 21-step adjustable
WALL: 17-step adjustable
SEAT F/R: 17-step adjustable
SEAT L/R: 17-step adjustable
REVERB time: 17-step adjustable
Depending on the sound field, some parameters
may not be adjustable (see page 21).
Equalizer BAND: BASS/TREBLE
Turnover frequency:
Bass: 99 Hz - 992 Hz
Treble: 1.0 kHz - 8.6 kHz
Level: ±10 dB, 0.5 dB step
Video section
Inputs 1 Vp-p 75 ohms
Outputs 1 Vp-p 75 ohms
General
System Preamplifier section:
Low-noise NF type equalizer
Power amplifier section:
Pure-complementary SEPP
Power requirements
230 V AC, 50/60 Hz
Power consumption
290 W
AC outlets 1 switched, maximum
100 W
430 × 155 × 350 mm
Dimensions
including projecting parts and controls
Mass (Approx.) 9.8 kg
Supplied accessories
See page 4.
Design and specifications are subject to change without
notice.
Getting Started
EN
27