Ryobi OPP1820 Traduction Des Instructions Originales page 4

any adjustments, changing accessories or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
■ Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
■ Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
■ Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
■ Use the power tool, accessories and tool bits etc,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
SERVICE
■ Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
ADDITIONAL GENERAL SAFETY WARNINGS
■ Some regions have regulations that restrict the use of
the product. Check with your local authority for advice.
■ Never allow children or people unfamiliar with the
instructions to use the product. Local regulations may
restrict the age of the operator.
■ Ensure before each use that all controls and safety
devices function correctly. Do not use the product if the
"off" switch does not stop the motor.
■ Wear full eye and hearing protection, strong sturdy
gloves as well as head protection while operating the
product; use a face mask if operation is dusty.
■ Do not wear loose fitting clothing, short trousers or
jewellery of any kind.
■ Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
■ Beware of thrown, flying or falling objects; keep all
bystanders, children, and animals at least 15 m away
from work area.
■ Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
■ Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay
extra attention to what is going on in the working area.
2
■ Operating similar tools nearby increases both the risk
of hearing injury and the potential for other persons to
enter your working area.
■ Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance and can
increase the risk of kickback.
■ Keep all parts of your body away from any moving part.
■ Inspect the product before each use. Check for correct
operation of all controls. Check for loose fasteners, make
sure all guards, and handles are properly and securely
attached. Replace any damaged parts before use.
■ Do not modify the machine in any way or use parts
and accessories which are not recommended by the
manufacturer.
■ Do not allow familiarity with the product to make you
careless. A careless fraction of a second is sufficient to
inflict serious injury.
■ Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of
the tool in unexpected situations.
■ Only use a weather proof extension cord. Check the
extension cord before every use for damage. Always
uncoil the extension cord during use because coiled
cords can overheat. Damaged extension cords should
not be repaired, they should be replaced with an
equivalent type.
WARNING
If the product is dropped, suffers heavy impact or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service center.
PRUNER SAFETY WARNINGS
■ Do not use the product when there is a possibility of
thunderstorm or lightning. Store the product safely
indoors.
■ Ensure all guards, handles are properly fitted and are
in good condition.
■ Do not start using the product until you have a clear
work area, secure footing, and a planned retreat path
away from the falling branches or limbs.
■ Beware of the emission of lubricant mist and saw dust.
Wear mask or respirator if required.
■ During operation, hold the product with both hands. Use
one hand to firmly grasp the front hand grip. Use the
other hand to grasp the rear handle and operate the
trigger release and on/off trigger.
■ Hold the power tool by insulated gripping surfaces only,
because the saw chain may contact hidden wiring.
English