Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
people or their property.
• Any use other than that expressly permitted in this user manual, can
lead to damage to the shredder and represent a serious hazard to the
The machine has been built according to the latest technology
and recognised safety rules. However, there is still a chance of
residual risks whilst working.
•
Injury from recoiling branches when feeding the hopper
•
Health risk from noise
•
Endangering health from electricity, when using inappropriate
1.
Feed hopper
2.
Adjustment wheel
3.
Frame for collection box
4.
Collection box
5.
Locking device
6.
Leg support
7.
Wheel
8.
Power supply
9.
Warning light
10. Switch to change rotational direction of the cylinder
11. On switch
12. Off switch
1.
Open the box and remove the machine and all accessories.
2.
Assembling the wheels (Fig.2)
•
Assemble both wheels (1), as shown in the image.
•
Clip the wheel covers (2) into the wheels (1).
GB
3.
Assembling the leg support (Fig.3)
•
Assemble both leg supports (1), as shown in the image.
4.
Connecting the upper part of the machine with the frame
•
Place the upper part of the machine on the ground with the feed
Warning! The shredder can only be started if the collection box
(Fig.1, No.4) has been pushed into the frame (Fig.1, No.3) and the
locking device (Fig.1, No.5) is in the upper position.
Control panel Fig.1
•
No.9 Warning light: When the shredder is in use, the warning
light shines brightly. When the shredder has been stopped, the
LED lamp goes off.
•
No.10 Manual change of rotational cylinder direction:
-
Button „▲" - anti-clockwise: When this button is pressed, the blade
cylinder rotates anti-clockwise. This is necessary when jammed
shredding material needs to be freed. This function is only availab-
le when the shredder is in operation.
-
Button „▲" - clockwise: This button switches the direction of the
blade cylinder from anti-clockwise back to clockwise.
•
No.11 On switch: Pressing this button starts the shredder and the
blade cylinder rotates clockwise.
•
No.12 Off switch: Pressing this button stops the shredder.
Automatic reverse
If the shredder is overloaded, e.g. if branches are too big, the
shredder stops automatically and the blade cylinder rotates anti-
clockwise independently for a few seconds. The shredder then
turns itself off after a few seconds.
user.
• The manufacturer is not liable for damage caused by unintended use
or incorrect operation.
Residual risks
connecting cables
•
Additionally, despite all the safety provisions, residual risks can
occur which are not obvious.
Residual risks can be minimised by complying with the "Safety
notices" and the "Intended use" as well as operating instructions
overall.
Equipment Fig. 1
Assembly
hopper (Fig.1, No.1) upside down.
•
Place the frame for the collection box (Fig.1, No.3) on the upper
part of the machine.
•
Bolt together both components using the four cross-head screws
provided in the holes intended for this (Fig.4, No.1).
5.
Positioning the collection box (Fig. 5)
•
Set the locking device (2) on the collection box to the lowest
position.
•
Completely push the collection box (1) into the frame (3).
•
Push the locking device (2) on the collection box (1) all the way to
the top again.
Commissioning
Working with the shredder
Alternating with branches, shred withered garden waste and bran-
ches that have been stored several days to prevent the shredder
from becoming blocked.
•
Make sure the collection box (Fig.1, No.4) is pushed into the frame
(Fig.1, No.3) correctly and the locking device (Fig.1, No.5) is in the
upper position.
•
Connect the shredder to the power supply.
•
Turn the shredder on by using the on switch (Fig.1, No.11).
•
The LED warning lamp (Fig.1, No.9) comes on.
•
Fill shredding material into the feed hopper (Fig.1, No.1) and it will
be drawn in.
•
Caution: If the shredding material becomes jammed, use the
switch to change the rotational direction of the cylinder (Fig.1,
No.10) so it runs anti-clockwise.
•
Make sure the shredder has completely shredded the input
material before adding new.
•
Do not use your hands to push in more shredding material. Use
the special pushing device or other shredding material.
•
When you have finished working with the shredder, turn it off and
disconnect it from the mains.
Emptying the collection box
•
Stop the shredder using the off button (Fig.1, No.12).
14
Publicité
Table des Matières
