Electric Connection; Cleaning, Maintenance And Repair - Scheppach GSE45S Manuel

• Set the locking device (Fig.1, No.5) to the lowest position.
• Pull out the collection box (Fig.1, No.4) and empty it.
• Re-insert the collection box (Fig.1, No.4) and push the locking
device (Fig.1, No.5) up again.
Setting the counter blade
The counter blade and the blade cylinder have been ideally
adjusted by the manufacturer. Re-adjusting the counter blade is
only required if it becomes worn. For maximum performance, it is
necessary that the distance between the counter blade and blade
cylinder is about 0.50 mm.
The installed electric motor is connected and operational. The connec-
tion complies with relevant VDE and DIN stipulations.
The customer's mains connection as well as the extension lead used
must comply with these provisions.
Hazardous electric connections
Insulation damage often occurs on electric connections.
Causes include:
• Pressure marks when connections are guided through windows and
doors
• Kinks due to inappropriate attachment or guidance of the connection
• Cuts when the connection is run over
• Insulation damage when being pulled out of the wall socket
• Tears from ageing insulation
Such hazardous electric connections must not be used and are dange-
rous to life due to the insulation damage.
Regularly check electric connections for damage. Make sure the
connection is not connected to the mains when checking. Electric
• Cleaning, maintenance and repair work may only be carried out
when the motor has been turned off and the machine has been
disconnected from the mains.
• Work on the electrical equipment, may only be carried out by
trained electricians.
• Wear gloves when handling the cylinder blade.
• Do not spray the shredder with water. Risk of electric shock.
• Always keep the machine, the wheels and the ventilation opening
clean. When cleaning, use a brush or a cloth, but not detergents or
solvents.
• Before every use, check the machine, and particularly safety devices,
for damage such as loose, worn or damaged parts. Check that all
Problem
Motor does not start.
Garden waste is not drawn in.
Shredding material is tangled.
Bei Fehlern, die Sie nicht selbst beheben können, wenden Sie sich bitte an den Service der Firma scheppach.
E-Mail: service@scheppach.com
Telefon: 00 49/82 23/ 40 02-99
Electric connection 

Cleaning, maintenance and repair

Troubleshooting
Possible cause
Collection box not in correct position
Motor is overloaded.
No electricity
Blade cylinder rotates anti-clockwise.
Shredding material is too soft.
Blade cylinder has become blocked.
Counter blade is not set correctly.
• Turn the shredder on.
• Turn the adjustment wheel (Fig.1, No.2) clockwise until you can
hear slight grinding sounds.
• When turning the adjustment wheel (Fig.1, No.2) clockwise by half
a turn, the blade cylinder is positioned closer to the counter blade
by 0.50 mm.
WARNING: If the shredder blade touches the counter blade, it will
be trimmed and small pieces of swarf may fall out of the ejection
opening. This is not an error, but it has to be re-adjusted to the
required degree because otherwise the counter blade will wear too
early.
connections must comply with relevant VDE and DIN stipulations. Only
use connections marked H 07 RN. Printing the type designation on the
connection is the law.
AC motor
• The power voltage has to be 230 Volt – 50 Hz.
• Extension leads up to 25 m in length must have a cross section of
1.5 mm , and at more than 25 m length, it has to be at least 2.5 mm
2
• The mains connection is protected against short circuit with a 16 A
slow fuse.
Connections and repairs to the electrical equipment may only be
carried out by a trained electrician.
If there are any questions, please provide the following data:
• Motor's type of power
• Data from the machine's type plate
When sending back the motor, always send the entire motor unit with
switch.
Follow the safety notices!
nuts, bolts and screws are tight.
• Check covers and safety devices for damage and correct positioning.
Replace if required.
• Store the machine in a dry location and beyond the reach of children.
Solution
Insert the collection box correctly and check
the locking device (see Commissioning).
Turn the shredder on again (see Commissio-
ning).
Have the socket, cable, lead and plug che-
cked by a trained electrician (see Electric
connection).
Change the rotational direction (see Commis-
sioning).
Push shredding material with special pushing
device for shredder.
Remove blockage (see Commissioning).
Re-adjust counter blade (see Commissioning).
15
.
2
GB