Ryobi ONE+ PBL375 Manuel D'utilisation page 9

WARNING:
Do not use nails with a shank smaller than 0.065 in. diam-
eter. Doing so may cause nails to exit the tool prematurely
through the guide track. Do not use hardened nails with
this tool. This could lead to excessive wear of the guide
body and allow nails to exit the back of the guide body,
leading to serious personal injury.
DEPTH OF DRIVE ADJUSTMENT
See Figure 6, page 13.
The depth-of-drive of the nail may be adjusted. It is advis-
able to test the depth on a scrap workpiece to determine
the required depth for the application.
To achieve the desired depth, use the depth-of-drive adjust-
ment on the tool.
„ Remove battery pack from the tool.
„ Turn the depth of drive adjustment left or right to change
the driving depth.
„ Reinstall battery and activate the tool by pressing the
worklight grip switch.
„ Drive a test nail after each adjustment until the desired
depth is set.
NOTE: Set depth of drive at the shallowest depth that will
meet your needs.
USING THE MODE SELECTOR SWITCH
See Figures 7 - 8, page 13.
WARNING:
Never wedge or hold back the workpiece contact mecha-
nism during operation of the tool. Doing so could result
in possible serious injury.
This tool is shipped from the factory with the mode selector
switch set in the Single Sequential Actuation mode. The mode
selector switch can also be set for Contact Actuation mode.
SINGLE SEQUENTIAL ACTUATION MODE
Single sequential actuation provides the most accurate nail
placement.
„ Remove battery pack from the tool.
„ Slide the selector to position ( ).
WARNING:
The nailer will not function properly if the selec-
tor is not securely seated in either position ( ) or
( ). Always assure the selector is seated properly to
avoid an unexpected nail discharge and possible serious
personal injury.
OPERATION
„ Reinstall battery and activate the tool by pressing the
grip switch.
„ Grip the tool firmly to maintain control. Position the nose
of the tool onto the work surface.
„ Push the tool against the work surface to depress the
workpiece contact.
„ Squeeze the trigger to drive a nail.
NOTE: Hold trigger until drive cycle is complete. If depress-
ing the trigger does not drive a nail, release the trigger and
lift the tool away from the workpiece, then replace and try
driving the nail again.
„ Always remove your finger from the trigger when the
desired number of fasteners has been driven.
CONTACT ACTUATION MODE
Contact actuation allows very fast repetitive nail placement.
„ Remove battery pack from the tool.
„ Slide the selector to position (
„ Reinstall battery and activate the tool by pressing the
worklight grip switch.
„ Grip the tool firmly to maintain control.
„ Squeeze and hold the trigger. Push the tool against the
work surface to depress the workpiece contact and drive
a nail. To drive another nail, lift the tool and press the
contact against the work surface again.
NOTE: Hold trigger and keep workpiece contact de-
pressed until drive cycle is complete.
„ Always remove your finger from the trigger when the
desired number of nails has been driven.
NOTE: In Contact Actuation Mode, the tool may also be
operated by pressing the workpiece contact against the
surface and squeezing the trigger.
WARNING:
During normal use the tool will recoil immediately
after driving a nail. This is a normal function of the
tool. Do not attempt to prevent the recoil by holding the
nailer against the workiece. Restriction to the recoil can
result in a second nail being driven from the nailer. Failure
to heed this warning can result in serious personal injury.
DRY-FIRE LOCKOUT
When the magazine has 0-8 nails remaining, the dry-fire
lockout feature will not allow continued operation.
The LED will flash rapidly when the last nail is used. It will
also flash rapidly if the Dry-Fire Lockout feature is engaged,
and the trigger is pulled. The tool needs to be reloaded.
To resume operation, remove battery pack and reload the
tool with nails.
NOTE: It is not necessary to remove the remaining nails.
9 — English
).