Transportation And Storage; Inspect The Delivery; Inspect The Unit; Transportation Guidelines - Xylem LOWARA ESH ATEX Manuel D'installation, D'exploitation Et De Maintenance

Montecchio Maggiore, 11.03.2016
Amedeo Valente
(Director of Engineering and
R&D)
rev.01
1.6.5 EU Declaration of Conformity
(No ATEX04)
1. Product model: see label on first page
2. Name and address of the manufacturer:
Xylem Service Italia S.r.l.
Via Vittorio Lombardi 14
36075 Montecchio Maggiore VI
Italy
3. This declaration of conformity is issued
under the sole responsibility of the
manufacturer.
4. Object of the declaration:
- pump
II 2G c IIC T4 Tamb -10 +55 °C
5. The object of the declaration described
above is in conformity with the relevant
Union harmonisation legislation: Directive
2014/34/EU of 26 February 2014
(equipment intended for use in potentially
explosive atmospheres)
6. References to the relevant harmonised
standards used or references to the other
technical specifications, in relation to
which conformity is declared: EN 1127-
1:2011, EN 15198:2007, EN 13463-
1:2009, EN 13463-5:2011
7. The notified body SGS Baseefa Limited
(NB 1180) performed the EU-type
examination and issued the certificate:
Baseefa16ATEX0067X
8. Additional information: the following
specific conditions of use apply.
–
The equipment must be suitably
earthed prior to operation.
– It is the user's responsibility to
ensure the equipment does not run
dry. Any control system used to
achieve this must comply with the
relevant requirements of EN 13463-
6.
–
For T4 operation the maximum
temperature of the process fluid
must not exceed +90°C.
Signed for and on behalf of:
Xylem Service Italia S.r.l.
Montecchio Maggiore, 11.03.2016
Amedeo Valente
(Director of Engineering and
R&D)
rev.01
Lowara is a trademark of Xylem Inc. or one of
its subsidiaries.

2 Transportation and Storage

2.1 Inspect the delivery

1. Check the outside of the package for
evident signs of damage.
2. Notify our distributor within eight days of
the delivery date, if the product bears
visible signs of damage.
Unpack the unit
1. Follow applicable step:
–
If the unit is packed in a carton,
then remove the staples and open
the carton.
–
If the unit is packed in a wooden
crate, then open the cover while
paying attention to the nails and
straps.
2. Remove the securing screws or the straps
from the wooden base.

2.1.1 Inspect the unit

1. Remove packing materials from the
product.
Dispose of all packing materials in
accordance with local regulations.
2. Inspect the product to determine if any
parts have been damaged or are missing.
3. If applicable, unfasten the product by
removing any screws, bolts, or straps.

Transportation guidelines

2.2
Precautions
WARNING:
 Observe accident prevention
regulations in force.
 Crush hazard. The unit and the
components can be heavy. Use
proper lifting methods and wear
steel-toed shoes at all times.
Check the gross weight that is indicated on the
package in order to select proper lifting
equipment.
Position and fastening
The pump or pump unit can be transported only
horizontally. Make sure that the pump or pump
unit is securely fastened during transportation
and cannot roll or fall over.
WARNING:
 Do not use eyebolts screwed on
the motor for handling the whole
electric pump unit.
 Do not use the shaft end of the
pump or of the motor to handle the
pump, the motor or the unit.

Eyebolts screwed onto the motor may be
exclusively used to handle the individual
motor or, in case of a not balanced
distribution of weights, to partially lift the
unit vertically starting from a horizontal
displacement.
Pump unit must always be fixed and
en - Original instructions
21