Applications And Technical Description; Applications; Product Description; Technical Data - Xylem LOWARA Sekamatik 10 E15M Manuel D'installation, D'utilisation Et D'entretien

regulations on electrical equipment). If work is
carried out on live electrical components, they
should be unplugged from the mains or the main
switch turned off and fuse unscrewed. A motor
protection switch is to be provided.
 Basically, all work on the pump or pump unit should
only be carried out when the pump is stationary and
not under pressure. All parts must be allowed to
return to ambient temperature. Make sure that no-
one can start the motor during such word. It is
essential that the procedure for stopping the system
described in the Operating Instructions is observed.
Pumps or pump systems that carry media that are
dangerous to health must be decontaminated before
being taken apart. Safety Data Sheets for the
various liquids handled. Immediately the work has
been completed, all safety and protective devices
must be replaced or restarted.
 Under EC machinery Directives, every machine
must be fitted with one or more emergency
command devices by which situations which
represent an immediate danger or which could later
be dangerous can be avoided.
 If the emergency command device is no longer
operated after an emergency "off" switch has been
triggered, this must be maintained by blocking the
emergency command device until it is released
again. It should not be possible to block the device
without this triggering an emergency "off" switch. It
should only be possible to release the device
through an appropriate action; this release should
not start the machine up again – it should only make
it possible to start it up again.
 If the power supply is interrupted or restored after
being interrupted or if it is changed in any other way,
this should not cause any danger (e.g. start up
without control or unexpected, pressure hammer).

2. Applications and Technical Description

2.1. Applications

The disposal unit SEKAMATIK 10E 15M is used for
pumping drainage water, waste water and sewage from
rooms which are below the sewer level.
The unit dispose sanitary installations like WC, hand
basins, washing machines and showers. With the
advantage of a ground level direct WC connection, it is
possible to place the unit directly on the back of the toilet.

2.2. Product description

Odour and gas-tight collection tank with a single stage
centrifual pump. The tank has a horizontal WC-inlet, a
vertical inlet on the top of the tank, a vertical air vent
and a clening cover.
The disposal unit SEKAMATIK 10E 15M is equipped with a
cutter system at the pump inlet which cuts all soft solids to
small particles, so that the liquid may be pumped through
small diameter discharge pipes of 1 ¼" Ø.
The disposal unit has equipped a pneumatic level control
with pressure switch.

2.3. Technical Data

Motor input P
1
Motor output P
2
Voltage
Nominal current
Speed
Insulation class
Degree of protection
Controller
Motor
Cable length
Cable type
Discharge
Utility volume
Weight

2.4. Operating Conditions

Maximum liquid temperature: 35°C, short term up to
60°C.
Density of pumped liquid: max. 1100 kg/m
Ph-value of pumped liquid: 5 up to 11.
Operation: The motor is designed for 40% S3 intermittent
operation.
Our standard warranty and maintenance regulations refer
to intermittent operation. For reduced warranty
periods and service intervals due to continuous operating
4conditions please contact our service department.

2.5. Explosive Environments

only models with explosion-proof motors (Ex model) must
be used.
classification (Ex-class) of the pump must be approved by
the local authorities.

3. Warranty

Our warranty only covers pumps which are installed and
operated in accordance with these installation and
operation instructions and accepted codes of good practice
and being used for the applications mentioned in these
instructions.

4. Transport and Storage

compensation hose to lift, lower or transport the unit.
horizontal position. Make sure that it cannot roll or fall
over. For longer periods of storage, the unit should be
protected against moisture, frost or heat.

5. Electrical Connection

5.1. General instructions

required electrical protection measures exist. The
connection to ground, earthing, isolating transformer, fault
current breaker or fault voltags circuit must correspond to
the guidelines set forth by the responsible power plant.
must correspond to the existing line voltage.
connections are installed flood- and moisture-safe. Before
starting operation check the cable and the plug against
damages.
1,5 kW
submerged in order to prevent water from penetrating
1,1 kW
through the cable into the motor.
230 V/50Hz
7,0 A
2900 U/min
standard as well as of explosion proof pumps must not be
H
not
14
For operation of the pumps in explosive environments
For each individual installation the explosion
Never use the cable, the control box or the pressure
The unit may be transported and stored in vertical or
Before operation, an expert check must secure that the
The voltage required in the technical data sheet
Make sure that the electrical pin-and-socket
The end of the pump power supply cable must not be
The normal separate motor starter/control box of
be installed in explosive envirom ents.
IP 54
IP 68
2,0 m
H07RN-F4G1,5
BSP 2" M
11 l
32 kg
3