Safety Instructions; Description And Specifications; Important; Installation - Xylem GOULDS LB Instructions D'installation, D'utilisation Et D'entretien

SAFETY INSTRUCTIONS

TO AVOID SERIOUS OR FATAL PERSONAL
INJURY OR MAJOR PROPERTY DAMAGE, READ
AND FOLLOW ALL SAFETY INSTRUCTIONS IN
MANUAL AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.
This is a SAFETY ALERT SYMBOL.
When you see this symbol on the
pump or in the manual, look for one
of the following signal words and
be alert to the potential for personal
injury or property damage.
Warns of hazards that WILL cause
DANGER
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause
WARNING
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause
CAUTION
personal injury or property damage.
NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.
THOROUGHLY REVIEW ALL INSTRUCTIONS
AND WARNINGS PRIOR TO PERFORMING ANY
WORK ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
UNIT NOT DESIGNED FOR USE
WARNING
WITH HAZARDOUS LIQUIDS OR
FLAMMABLE GASES. THESE
FLUIDS MAY BE PRESENT IN
CONTAINMENT AREAS.
Hazardous fluids can
cause fire, burns
or death.

DESCRIPTION and SPECIFICATIONS:

The Model LB is a single stage, centrifugal jet pump
for general liquid transfer service and booster appli-
cations. The liquid end utilizes a 304SS stamped cas-
ing, Noryl ® impeller, Lexan ® ejector and guidevane,
Amodel ® motor adapter and EPR o-rings. All motors
are NEMA 48Y and 56Y square flange with a 304SS
threaded shaft extension.

1. IMPORTANT

1.1 Inspect unit for damage. Report any damage to
carrier/dealer immediately.
1.2 Electrical supply must be a separate branch circuit
with fuses or circuit breakers, wire sizes, etc., in
compliance with National and Local electrical codes.
Install an all-leg disconnect switch near pump.
ALWAYS DISCONNECT ELECTRICAL
CAUTION
POWER WHEN HANDLING PUMP OR
CONTROLS.
1.3 Motors must be wired for proper voltage. Mo-
tor wiring diagram is on motor nameplate. Wire
size must limit maximum voltage drop to 10% of
nameplate voltage at motor terminals, or motor
life and pump performance will be lowered.
1.4 Always use horsepower-rated switches, contactor
and starters.
1.5 Motor protection
1.5.1 Single-phase: Thermal protection for single-
phase units is sometimes built in (check
nameplate). If no built-in protection is provid-
ed, use a contactor with a proper overload.
Fusing is permissible.
1.5.2 Three-phase: Provide three-leg protection
with properly sized magnetic starter and
thermal overloads.
1.6 Maximum Operating Limits:
Liquid Temperature: 140ºF (60ºC)
Working Pressure:
Starts per Hour:
1.7 Regular inspection and maintenance will increase
service life. Base schedule on operating time.
Refer to Section 8.

2. INSTALLATION

2.1 Locate pump as near liquid source as possible
(below level of liquid for automatic operation).
2.2 Protect from freezing or flooding.
2.3 Allow adequate space for servicing and ventilation.
2.4 All piping must be supported independently of
the pump, and must "line-up" naturally.
NEVER DRAW PIPING IN PLACE BY
CAUTION
FORCING THE PUMP SUCTION AND
DISCHARGE CONNECTIONS.
2.5 Avoid unnecessary fittings. Select sizes to keep
friction losses to a minimum.
2.6 Units may be installed horizontally, inclined or
vertically.
DO NOT INSTALL WITH MOTOR
CAUTION
BELOW PUMP. ANY LEAKAGE OR
CONDENSATION WILL AFFECT THE MOTOR.
2.7 Foundation must be flat and substantial to elimi-
nate strain when tightening bolts. Use rubber
mounts to minimize noise and vibration.
2.8 Tighten motor hold-down bolts before connect-
ing piping to pump.

3. SUCTION PIPING

3.1 Low static suction lift and short, direct, suction pip-
ing is desired. Consult pump performance curve
for Net Positive Suction Head Required.
85 PSI
20, evenly distributed.
3