Safety Instructions; Description And Specifications; Engineering Data; Installation Location - Xylem GOULDS 3642 Directives D'installation, D'utilisation Et D'entretien

SAFETY INSTRUCTIONS

TO AVOID SERIOUS OR FATAL PERSONAL
INJURY OR MAJOR PROPERTY DAMAGE, READ
AND FOLLOW ALL SAFETY INSTRUCTIONS IN
MANUAL AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.
This is a SAFETY ALERT SYMBOL.
When you see this symbol on the
pump or in the manual, look for one
of the following signal words and
be alert to the potential for personal
injury or property damage.
Warns of hazards that WILL cause
DANGER
serious personal injury, death or
major property damage.
Warns of hazards that CAN cause
WARNING
serious personal injury, death or
major property damage.
Warns of hazards that CAN cause
CAUTION
personal injury or property damage.
NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.
THOROUGHLY REVIEW ALL INSTRUCTIONS AND
WARNINGS PRIOR TO PERFORMING ANY WORK
ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
UNIT NOT DESIGNED FOR USE
WARNING
WITH HAZARDOUS LIQUIDS OR
FLAMMABLE GASES. THESE
FLUIDS MAY BE PRESENT IN
CONTAINMENT AREAS.
Hazardous fluids can
cause fire, burns
or death.
This product can expose you to
WARNING
chemicals including Lead which is
known to the state of California to cause cancer or
birth defects or other reproductive harm. For more
information go to: www.P65Warnings.ca.gov.

DESCRIPTION and SPECIFICATIONS:

The 3642 (closed-coupled) and 3742 (frame-mounted)
are single stage, end suction, centrifugal pumps for
water circulation, booster service, liquid transfer,
spraying systems, jockey pump and general service
pumping. Pumps are available in three different ma-
terials of construction: all iron, bronze-fitted and all
bronze.
Pump impellers are enclosed design for high efficien-
cy, threaded directly on the motor shaft.
Close-coupled units have NEMA standard frame mo-
tors with C-face mounting and threaded shaft exten-
sions. Frame mounted units can be coupled to motors
through a spacer coupling, or belt driven.

ENGINEERING DATA

Maximum Liquid Temperature:
212º F (100º C) – standard seal
250º F (120º C) – Optional high temp. seal
Maximum Working Pressure: 125 psi
All manuals and user guides at all-guides.com
Starts per Hour: 20 - Evenly distributed
INSTALLATION
Location:
Locate pump as near liquid source as practical; below
level of liquid for repriming capability.
Allow adequate space for servicing and ventilation.
Protect the unit from weather and water damage due
to rain, flooding or freezing temperatures.
Close - Coupled Units
Units may be installed horizontally, inclined or
vertically with the motor above the pump.
NOTICE: DO NOT INSTALL WITH MOTOR BELOW

Foundation:

A flat and substantial foundation surface MUST be
provided to avoid distortion and/or strain when
tightening the foundation bolts. A rubber mounting is
acceptable to reduce noise or excessive vibration.
Tighten motor hold-down bolts BEFORE connecting
piping to pump.
Bedplate must be grouted to a foundation with solid
footing. Refer to Figure 1.
Place unit in position on wedges located at four
points, two below approximate center of driver and
two below approximate center of pump. Adjust wedg-
es to level unit. Level or plumb suction and discharge
flanges.
Make sure bedplate is not distorted and final coupling
alignment can be made within the limits of movement
of motor and by shimming, if necessary.
Tighten foundation bolts finger tight and build dam
around foundation. Pour grout under bedplate mak-
ing sure the areas under the pump and motor feet
3642/3742
Model Suction
1 x 1¼ - 5 1¼" NPT
1¼ x 1½ - 5 1½" NPT
PUMP. ANY LEAKAGE OR CONDENSATION
WILL AFFECT THE MOTOR.
Frame-Mounted Units:
(1/4")
Finished grouting
(1/2 to 3/4")
Allowance
for leveling
Wood
frame
Figure 1
Discharge
1" NPT
1¼" NPT
Grout hole Base
Grout
Leveling wedges or shims—left in place
Top of foundation—
clean and wet down
Sleeve
Washer
Lug
3