Troubleshooting Guide; Replacement Parts And Optional Parts - Horizon Hobby ParkZone F4F Wildcat BNF Manuel D'utilisation

EN

Troubleshooting Guide

Problem
• Aircraft will not respond to throttle
but responds to other controls
• Extra propeller noise or extra
vibration
• Reduced flight time or aircraft
underpowered
• LED on receiver flashes and aircraft
cannot be controlled by transmitter
• Control surface does not move, or is
slow to respond to control inputs.
• Controls reversed
• Motor loses power
• Motor power pulses then motor
loses power

Replacement Parts and Optional Parts

Number Description
PKZ1902 Decal Sheet
FLO505380 Gull Gray Light 36440 1/2oz Polly Scale
TES4847 Acryl 1/2oz US Navy Blue Gray
PKZ1906 Simulated Landing Gear Wheels
PKZ1907 Tailwheel
PKZ1913 Complete Canopy w/ Pilot
PKZ1918 Prop Adapter & Hub
PKZ1920 Painted Wing
PKZ1921 Landing Skid
PKZ1922 Pushrod Set
PKZ1923 Control Horn Set
PKZ1924 Horizontal Tail w/ Access
PKZ1926 Painted Cowl
PKZ1928 Motor Mount
PKZ1929 Hook And Loop Set
PKZ1063 Y harness (ailerons)
16
Possible Cause
• Throttle not at idle at control setup so
throttle not armed
• Throttle channel is reversed
• Damaged propeller, motor or motor mount
• Loose propeller and propeller adapter
• Propeller installed backwards
• Flight battery charge is low
• Propeller installed backwards
• Flight battery damaged
• Less than a five (5) second wait after
powering transmitter and before connecting
flight battery to aircraft
• Transmitter too close to aircraft during
binding process
• Transmitter bound to another aircraft
• Batteries in transmitter low
• Control surface, control horn, linkage or
servo damage
• Wire damaged or connections loose
• Parts not secured in fuselage
• Transmitter settings reversed
• Damage to motor, or power components
• ESC uses default soft Low Voltage Cutoff
(LVC)
Number
PKZ4421
PKZ1967
PKZ1970
PKZ1019
PKZ1033
HBZ1003
PKZ1080
PKZ1081
PKZ1814
PKZ4416
SPMAR500
SPMR5500
SPMR7700
SPMR6600
PKZ1040
Solution
• Reset controls with throttle stick and
throttle trim at lowest setting
• Reverse throttle channel on transmitter
• Replace damaged parts
• Tighten parts for propeller and propeller
adapter
• Remove and install propeller correctly
• Completely recharge flight battery
• Remove and install propeller correctly
• Replace flight battery and obey flight
battery instructions
• Disconnect then connect flight battery to
aircraft
• Move powered transmitter a few feet
from aircraft, disconnect and connect
flight battery to aircraft
• Bind transmitter to aircraft receiver
• Replace transmitter batteries
• Replace or repair damaged parts and
adjust controls
• Do a check of wires and connections,
connect or replace as needed
• Make hook and loop fastenings tight so
no parts move in fuselage
• Do the Control Direction Test and adjust
controls on transmitter appropriately
• Do a check of batteries, transmitter,
receiver, ESC, motor and wiring for
damage (replace as needed)
• Recharge flight battery
Description
Clevis set (4)
Painted Bare Fuselage
Replacement Airframe
9 x 6 propeller
3S 11.1V 1300mAh LiPo battery
3S LiPo balancing charger (DC)
9 gram servo (elevator and rudder)
9 gram long lead servo (ailerons)
18A BL ESC
480 brushless outrunner (960 Kv)
5 channel sport receiver
DX5E TX only (optional)
DX7 TX only (optional)
DX6i TX only (optional)
DC 2-3S balancing charger (optional)