Scheppach AG600 Traduction De La Notice Originale page 21

The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Before starting the equipment
Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Warning! Always pull the power plug before ma-
king adjustments to the equipment.
Fitting the additional handle (Fig. 2)
• The angle grinder must not be used without the ad-
ditional handle (3).
• The additional handle can be secured in any of 2
positions (A, B).
Tool side
Left (position A / as shown)
Right (position B)
Setting the guard (Fig. 3)
Warning!
• Switch off the tool. Pull the power plug.
• Adjust the guard (4) to protect your hands so that
the material being ground is directed away from
your body.
• The position of the guard (4) can be adjusted to any
specific working conditions. Undo the screw (a) and
turn the cover (4) into the required position.
• Ensure that the guard (4) correctly covers the gear
wheel casing.
• Retighten the screw (a).
• Ensure that the guard (4) is secure.
m Take care that the safety device is secure.
m Never use the angle grinder without the guard.
Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at least
1 minute with the grinding or cutting wheel fi tted in
place. Vibrating wheels are to be replaced immedi-
ately.
Operation
Switching on/off (Fig. 4)
The on/off switch is equipped with a safety system.
To switch on, press the on/off switch (2) on the rear
part down and slide it forwards.
To switch off, simply release the on/off switch (2).
m Wait until the machine has reached its top
speed. You can then position the angle grinder
on the workpiece and machine it.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Suitable for
Right-handed users
Left-handed users
Changing the grinding wheels (Fig. 5)
Use the face spanner (5) supplied to change the grin-
ding wheels.
Warning!
Pull out the power plug.
• Simple wheel change by spindle lock:
• Press the spindle lock and allow the grinding wheel
to latch in place.
• Open the flange nut with the face spanner.
• Change the grinding or cutting wheel and tighten
the flange nut with the face spanner.
Notice!
Only ever press the spindle lock when the mo-
tor and grinding spindle are at a standstill! You
must keep the spindle lock pressed while you
change the wheel!
For grinding or cutting wheels up to approx. 3 mm
thick, screw on the fl ange nut with the fl at side fac-
ing the grinding or cutting wheel.
Flange arrangements when using grinding
wheels and cutting wheels (Fig. 6-9)
• Flange arrangement when using a depressed-
centre or straight grinding wheel (Fig. 7)
a) Clamping flange
b) Flange nut
• Flange arrangement when using a depressed-
• entre cutting wheel (Fig. 8)
a) Clamping flange
b) Flange nut
• Flange arrangement when using a straight cutting
wheel (Fig. 9)
a) Clamping flange
b) Flange nut
Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilation
holes clean at all times.
Grinding Wheels
• Never use a grinding or cutting wheel bigger than
the specified diameter.
• Before using a grinding or cutting wheel, check its
rated speed.
• The maximum speed of the grinding or cutting
wheel used must be higher than the idle speed of
the angle grinder.
• Use only grinding and cutting wheels that are ap-
proved for a minimum speed of 11500 min
peripheral speed of 80 m/s.
• Check the direction of rotation when you use dia-
mond cutting wheels. The directional arrow on the
diamond cutting wheel must point in the direction in
which the tool rotates.
Take special care that the grinding/sanding wheels
are properly stored and transported. Ensure that the
grinding/sanding wheels are never exposed to shock,
jolts or sharp edges (for example during transport or
storage in a toolbox). This could cause damage (such
as cracks) to the grinding/sanding wheels and place
and a
-1
GB І 21