Publicité
Les langues disponibles
Les langues disponibles
WARNING:
Fasteners must be driven
straight into the material. Do not tilt nailer
while driving fasteners. Refer to Fig. 8.
WARNING: Metal connector nails are
not designed to penetrate metal. When
installing metal connectors, ALWAYS
place the hole locating tip into the metal
connector's pre-formed hole, and orient
so the nail is perpendicular to the hole
before attempting to drive a fastener.
Refer to Figure 9.
SEQUENTIAL MODE
The sequential mode is used for intermittent nailing. It
offers the maximum battery life for driving nails.
1. Using the mode selector switch (I), select the
sequential mode ( ).
2. Release the trigger safety lock-off (B).
3. Place the hole locating tip (M) into the first hole
on the metal connector and press down on the
tool.
4. Pull the trigger switch (A) to actuate the tool.
5. Release the trigger and raise the nailer from the
work surface.
6. Repeat steps 3–5 to actuate the next nail.
RAPIDCYCLE SEQUENTIAL MODE
In RapidCycle sequential mode, the motor rotation
speed is automatically restored after driving a nail
to allow fast consecutive nailing, but with all of the
health & safety benefits of a sequential actuating
pattern. While offering the ability to drive more nails
in less time, this mode more quickly depletes the
battery charge.
1. Use the mode selector switch (I) to select the
RapidCycle sequential mode (
2. Release the trigger safety lock-off (B).
3. Place the hole locating tip (M) into the first hole
on the metal connector and press down on the
tool.
4. Pull the trigger switch (A) to actuate the tool.
5. Release the trigger and raise the nailer from the
work surface.
NOTE: The tool motor returns to full speed
automatically without the contact tip (C) being
depressed.
6. Repeat steps 3–5 to actuate the next nail.
LED Indicator (Fig. 1)
Your nailer is equipped with two LED indicator
lights (E) located on the back of the tool just below
the back cap. Also refer to to the Troubleshooting
Guide for further instruction.
All manuals and user guides at all-guides.com
+/OR
Stall Release (Fig. 1, 3)
If the nailer is used in rigorous application where
all available energy in the motor is used to drive
a fastener, the tool may stall. The driver blade
did not complete the drive cycle and the jam/
stall indicator (E) will flash. Rotate the stall release
lever (F) on the tool and the mechanism will release.
If the driver blade does not automatically return to
the home position, proceed to Clearing a Jammed
Nail. If the unit continues to stall please review the
mode selection, material and fastener length to be
).
sure that it is not too rigorous an application.
DCN693
If continuous stalling occurs, review speed selection.
Depending upon the application, a different speed
setting may be necessary.
Clearing a Jammed Nail (Fig. 1, 3)
If a nail becomes jammed in the nosepiece, the
jam/stall indicator light (E) will flash.
LOW BATTERY
Replace battery with a
charged pack.
HOT PACK
Let the battery cool or
replace it with a cool pack.
JAM/STALL CONDITION
Rotate the stall release
lever to release. Refer to
Stall Release.
HOT TOOL
Let the tool cool down
before continuing use.
ERROR
Reset tool by removing
and reinserting battery
pack or cycling trigger
lock off. If error code
or any other
persist, take tool to an
combination.
authorized D
service center.
WARNING: Always engage the trigger
safety lock-off (B) and disconnect battery
pack and unload fasteners before
attempting to clear a jam.
CAUTION: When removing a jammed
nail, DO NOT orient the nailer with the
nose up or with the battery foot up.
Positioning the nailer this way makes the
jammed nail or pieces of the nail more
english
WALT
e
55
Publicité
