Audio Setup - Denon AVR-1611 Manuel De L'utilisateur

ENGLISH
Manual Setup

Audio Setup

Make settings for audio playback.
Setting items
2ch DIRECT/STEREO Setting : Select the method for setting the speakers used in the 2-channel
Select the method for direct and stereo playback modes.
setting the speakers used • Basic : The settings at "Speaker Setup" (vpage 49) are applied.
in the 2-channel direct and • Custom : Make separate settings for 2-channel. Make the following
stereo playback modes. settings:
Front : Set the front speaker size.
• Large : Use a large speaker that can adequately play back low
frequencies.
• Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
If "Speaker Config." – "Subwoofer" (vpage 49) is set to "No", the
setting is automatically set to "Large".
Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
If "Speaker Config." – "Subwoofer" (vpage 49) is set to "No", the
setting is automatically set to "No". If the "Front" setting is "Small",
the setting is automatically "Yes".
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
• LFE : When the "2ch DIRECT/STEREO" – "Front" setting is set to
"Large", the LFE signal alone is output from the subwoofer. Also, when
the "2ch DIRECT/STEREO" – "Front" setting is set to "Small", the front
channel low range signal is added to the LFE signal output from the
subwoofer.
• LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This setting can be set made "2ch DIRECT/STEREO" – "Subwoofer"
is set to "Yes".
Crossover : Set the maximum frequency of the bass signal output from
each channel to the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• This setting can be set made "2ch DIRECT/STEREO" – "Subwoofer" is
set to "Yes".
• If the "2ch DIRECT/STEREO" – "Front" setting is "Large" and the
"Subwoofer Mode" setting is "LFE", "Full Band" is displayed and the
setting cannot be made.
52
Remote control operation
buttons
Default settings are underlined.
Setting details
Move the cursor
(Up/Down/Left/Right)
Setting items
2ch DIRECT/STEREO Distance FL / Distance FR : Select the speaker.
(Continued) • 0.0ft – 60.0ft (12.0ft) / 0.00m – 18.00m (3.60m) : Set the distance to
the speaker.
Set so that the difference between the front left speaker and front
right speaker distances is 6.0 m (20.0 ft) or less.
Level FL / Level FR : Select the speaker.
• –12.0dB – +12.0dB (0.0dB) : Adjust the level of each channel.
Auto Surround Mode ON : Memorize settings. Automatically play with the last used surround
Make setting for mode.
memorizing surround mode OFF : Do not memorize settings. Surround mode does not change
setting for each input signal according to input signal.
type.
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals
listed below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r LPCM Multi-channel signals
EQ Customize Audyssey Byp. L/R : Set when not using "Audyssey Byp. L/R" equalizer.
Set so that unused equalizer • Used : Use.
settings are not displayed • Not Used : Do not use.
MULTEQ
when is pressed.
Set so that "Audyssey Byp. L/R" settings can be made when
Audyssey Auto Setup is performed.
Audyssey Flat : Set when not using "Audyssey Flat" equalizer.
• Used : Use.
• Not Used : Do not use.
Set so that "Audyssey Flat" settings can be made when Audyssey
Auto Setup is performed.
Manual : Set when not using the "Manual" equalizer.
• Used : Use.
• Not Used : Do not use.
The equalizer mode in which
"Not Used" is selected
cannot be stored and
recalled in the Quick Select
function.
Confirm the setting
Setting details
Return to previous menu