Resetting The Microprocessor - Denon AVR-1611 Manuel De L'utilisateur

Masquer les pouces Voir aussi pour AVR-1611:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

ENGLISH
GHDMIH
Symptom
No audio is
• Check the connection of the HDMI connectors.
output with HDMI
• When outputting HDMI audio from the speakers, set "HDMI
connection.
Audio Out" on the menu to "Amp".
• When outputting HDMI audio from a TV, set "HDMI Audio Out"
on the menu to "TV".
No video is
• Check the connection of the HDMI connectors.
output with HDMI
• Set the input source to match the connected HDMI connector.
connection.
• Check whether the TV is compatible with copyright protection
(HDCP). If connected to a device not compatible with HDCP, video
will not be output correctly.
When the following
• Set "HDMI Control" on the menu to "OFF". To operate power
operations are
only for each device, set "Power Off Control" to "OFF".
performed on
devices compatible
with HDMI control,
the same operations
occur on this unit.
• Power ON/OFF
• Switching
audio
output devices
• Adjust volume
• Switch input source
GRadioH
Symptom
Reception fails, or
• Change the antenna orientation or position.
there is a lot of noise
• Separate the AM loop antenna from the unit.
or distortion.
• Use an FM outdoor antenna.
• Separate the antenna from other connection cables.
GiPodH
Symptom
iPod cannot be
• Check the iPod connections.
played.
• Plug the control dock for iPod's AC adapter into a power outlet.
• Switch the input source to "DOCK".
"Connection Error"
• Unable to communicate properly. Turn off the power to this unit,
is displayed.
disconnect the iPod and then reconnect it.
"Not Support" is
• The iPod connected to the unit is not compatible. Please make
displayed.
sure the iPod you are connecting is compatible.
• The software version of the connected iPod is an old one. Please
update to the latest version.
"Connection Error"
• The iPod is not responding. Turn off the power to this unit,
is displayed.
disconnect the iPod and then reconnect it.
72
Cause/Solution
14, 19, 20
Cause/Solution
Cause/Solution
GRemote control unitH
Page
Symptom
14
The set cannot be
• Batteries are worn out. Replace with new batteries.
51
operated with the
• Operate the remote control unit within a distance of about 23 ft /
remote control unit.
7 m from this unit and at an angle of within 30°.
51
• Remove any obstacle between this unit and the remote control
unit.
• Insert the batteries in the proper direction, checking the q and
14
w marks.
• The set's remote control sensor is exposed to strong light (direct
14
sunlight, inverter type fluorescent bulb light, etc.). Move the set
to a place in which the remote control sensor will not be exposed
to strong light.
32, 51

Resetting the microprocessor

Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
ON/STANDBY
Page
18
18
18
18
1
Page
Turn off the power using
18
2
Press
ON/STANDBY
19, 20
SURROUND MODE 1
3
Once the display starts flashing at intervals of about 1 second, release the two
21
buttons.
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
Cause/Solution
SURROUND MODE 1
SURROUND MODE 0
ON/STANDBY
.
while simultaneously pressing
SURROUND MODE 0
.
Page
64
64
64
64
64
and

Publicité

Table des Matières
loading

Table des Matières