LOOSE ACCESSORIES:
MN - High and low pressure gauges. One for each refrigerant circuit.
CR - Remote control panel. To be included in the room for remote control of the unit, with the
same functions as that inserted in the machine.
IS - RS 485 serial interface. For connection to centralized control and supervision systems.
PV2 - 2-ways pressostatic valve .tTo control the condensation.
PV3 - 3-ways pressostatic valve. To control the condensation.
AG - Rubber vibration dampers. To be inserted at the bottom of the unit to dampen possible
vibrations due to the type of floor where the machine is installed.
FL - Flow switch. Inserted to protect the evaporator from possible water flow interruptions.
REFERENCE CONDITIONS
All technical data, indicated on pages 8 and 9, refer to the following unit operating conditions:
- cooling:
• inlet water temperature 12 °C
• outlet water temperature 7 °C
• condenser entering water temperature 30 °C.
• condenser leaving water temperature 35 °C.
- heating:
• inlet water temperature 40°C.
• outlet water temperature 45°C.
• evaporator entering water temperature 15 °C.
• evaporator leaving water temperature 10 °C.
- sound pressure level (DIN 45635):
measured in free field conditions at 1 m from the unit and at 1,5 m from the ground. According
to DIN 45635.
- sound pressure level (ISO 3744):
measured in free field conditions at 1 m from the unit. As defined by ISO 3744.
The power supply is 400V/3Ph/50Hz; auxiliary supply is 230V/1Ph/50Hz.
OPERATING RANGE
Evaporator inlet water temperature
Evaporator outlet water temperature
Evaporator water thermal difference (1)
Condenser inlet water temperature
Condenser outlet water temperature
Condenser water thermal difference (1)
Min. chilled water/glycol temperature
Max. operating pressure evaporator water side
Max. operating pressure condenser water side
*
The low temperature kit accessory (BT) is required in case the unit will work with evaporator's outlet water
temperature below 5 °C.
(1) In all cases the water range will have to re-enter within the reported limits on pagg. 16-17.
6
CWW/K 726÷36012
COOLING
RAFFREDDAMENTO
min
max
°C
8
°C
5*
°C
3
°C
10
°C
25
°C
4
°C
kPa
kPa
ACCESSORI FORNITI SEPARATAMENTE:
MN - Manometri alta/bassa pressione. Uno per ogni circuito frigorifero.
CR - Pannello comandi remoto. Da inserire in ambiente per il comando a distanza dell'unità, con
funzioni identiche a quello inserito in macchina.
IS - Interfaccia seriale RS 485. Per collegamento a sistemi di controllo e di supervisione centralizzati.
PV2 - Valvola pressostatica a 2 vie. Per il controllo della condensazione.
PV3 - Valvola pressostatica a 3 vie. Per il controllo della condensazione.
AG - Antivibranti in gomma. Da inserire alla base dell'unità per smorzare eventuali vibrazioni
dovute al tipo di pavimento ove la macchina è installata.
FL - Flussostato. Inserito a protezione dell' e vaporatore da possibili interruzioni del flusso d'acqua.
CONDIZIONI DI RIFERIMENTO
I dati tecnici, indicati a pagina 8 e 9 si riferiscono alle seguenti condizioni di funzionamento:
- in raffreddamento:
• temperatura ingresso acqua12 °C
• temperatura uscita acqua 7 °C
• temperatura ingresso acqua al condensatore 30 °C.
• temperatura uscita acqua al condensatore 35 °C.
- in riscaldamento:
• temperatura ingresso acqua 40 °C
• temperatura uscita acqua 45 °C
• temperatura ingresso acqua all'evaporatore 15 °C.
• temperatura uscita acqua all'evaporatore 10 °C.
- pressione sonora (DIN 45635):
rilevata in campo libero a 1 m di distanza dall'unità e ad 1,5 m dal suolo. Secondo normativa DIN 45635.
- pressione sonora (ISO 3744):
rilevata in campo libero a 1 m di distanza dall'unità. Valore medio definito dalla ISO 3744.
L'alimentazione elettrica di potenza é 400V/3Ph/50Hz; l'alimentazione elettrica ausiliaria é
230V/1Ph/50Hz.
HEATING
RISCALDAMENTO
min
max
20
25
45
15
30
50
9
3
10
45
8
20
50
5
15
12
3
9
- 8*
1000
1000
*
L'accessorio bassa temperatura (BT) è necessario nei casi di funzionamento dell'uni tà in condizioni di uscita
dell'acqua all'evaporatore inferiore ai 5 °C.
(1) In ogni caso la portata d'acqua dovrà rientrare nei limiti riportati a pagg. 16-17.
LIMITI DI FUNZIONAMENTO
Temperatura acqua in ingresso evaporatore
Temperatura acqua in uscita evaporatore
Salto termico acqua evaporatore (1)
Temperatura acqua in ingresso condensatore
Temperatura acqua in uscita condensatore
Salto termico acqua condensatore (1)
Minima temperatura dell'acqua refrigerata con
l'impiego di glicole
Max. pressione di esercizio lato acqua evaporatore
Max. pressione di esercizio lato acqua condensatore