Solution Filter Cleaning; Battery Charge - Nilfisk SCRUBBER-DRYER BA 430S Manuel D'emploi Et D'entretien

USE AND MAINTENANCE MANUAL

SOLUTION FILTER CLEANING

1. Rotate and close the solution tap (5, Fig. F). If the tap
is not fitted on the machine, empty the tank (6, Fig. H)
as described in the specific paragraph.
2. Drive the machine on a level ground.
3. Check the switches (5 and 6, Fig. B) are in "0"
position.
4. Operating under the right lower side of the machine,
remove the transparent cover (1, Fig. F) and the wire
gauze (2), clean and reinstall them on the support (3).
NOTE
The wire gauze (2) must be correctly
positioned on the support (3) housing (4).

BATTERY CHARGE

NOTE
Charge the batteries when the warning light
(3 or 4, Fig. B) turns on and at the end of
every cleaning.
Keeping the batteries charged makes their
life last longer.
CAUTION!
When the batteries are discharged, recharge
them as soon as possible not to shorten
their life.
Check for battery charge at least once a
week.
CAUTION!
The battery charger must be appropriate to
the battery installed on the machine.
WARNING!
Battery charging produces explosive
hydrogen gas. Charge the batteries only in
well-ventilated areas and far from naked
flames.
Do not smoke during battery charging.
Keep the tank assembly open while
recharging the battery.
WARNING!
Pay attention during battery recharging
because there can be battery fluid leakages.
The battery fluid is corrosive. If it comes in
contact with the skin or eyes, rinse
thoroughly with water and consult a
physician.
14
1. Drive the machine on a level ground.
2. Remove the key (24, Fig. C) from its housing and
remove the tank assembly fastening screw (1, Fig.
H).
3. Carefully lift the tank assembly (19, Fig. H) using the
handlebar (2, Fig. C).
4. For lead batteries only:
– Check the correct level of electrolyte inside the
battery; if necessary, top up through the caps (14,
Fig. H);
– Leave the caps (14) open for next recharging;
– Clean (if necessary) the upper surface of the
battery.
5. Proceed with recharging the battery according to one
of the following ways, depending on the presence of
the electronic battery charger (16, Fig. H).
Charging the battery with an exterior battery
charger
1. Check that the battery charger is adequate referring
to the Battery Manual. The rated battery charger
voltage is 24 V.
2. Disconnect the battery connector (25, Fig. C) and
connect it to the external battery charger.
3. Connect the battery charger to the electrical system.
4. When the recharging is complete, disconnect the
battery charger from the electrical system and from
the battery connector (25, Fig. C).
5. (for lead batteries only) Check the correct level of
electrolyte inside the battery; if necessary, top up
through the caps and close all the caps (14, Fig. H).
6. Reconnect the battery connector (25, Fig. C) to the
machine.
7. Carefully lower the tank assembly (19, Fig. H) using
the handlebar (2, Fig. C).
8. Remove the key (24, Fig. C) from its housing and
tighten the tank assembly fastening screw (1, Fig. H).
9. Now the machine is ready to be used.
Battery charging with optional battery charger
installed on the machine
1. For lead batteries only:
– Check the correct level of electrolyte inside the
battery; if necessary, top up through the caps (14,
Fig. H);
– When the correct level is reached, close the caps
(14) and clean (if necessary) the upper surface of
the battery.
2. Connect the battery charger electrical connector (22,
Fig. C) to the electrical system (the system voltage
and frequency must be compatible with the battery
charger values: see the Battery Charger Manual).
08812942(3)2004-05 A