Riester e-scope Mode D'emploi page 19

Directives and manufacturer's declaration -­ Electromagnetic immunity
The e-­scope® instruments are intended for use in the electromagnetic environment specified below. The customer or
user of the e-­scope® should ensure that it is used in such an environment.
Immunity testing IEC 60601 test level
Guided RF
Diturbances acc.
3 Vrms
to
0,5 MHz bis 80MHz
IEC61000-­4-­6
6 V in ISM frequency
bands between 0.15
MHz and 80 MHz
80% AM at 1 kHz
Radiated RF 3 V/m
IEC 61000-­4-­3 80 MHz to 2.7 GHz
Proximity fields 380 -­ 390 MHz
from RF wireless 27 V/m;; PM 50%;; 18 Hz
communications 430 -­ 470 MHz
equipment
28 V/m;; (FM ±5 kHz, 1
kHz sine)
PM;; 18 Hz11
704 -­ 787 MHz
9 V/m;; PM 50%;; 217 Hz
800 -­ 960 MHz
28 V/m;; PM 50%;; 18 Hz
1700 -­ 1990 MHz
28 V/m;; PM 50%;; 217
Hz
2400 -­ 2570 MHz
28 V/m;; PM 50%;; 217
Hz
5100 -­ 5800 MHz
9 V/m;; PM 50%;; 217 Hz
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
a field strengths of fixed transmitters, such. B. Base stations for radio (cellular / cordless) telephones and land
mobile radios, amateur radio, AM and FM broadcasting and television broadcasting can not be predicted
theoretically accurately. To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic examination should be considered. If the measured field strength at the location where the e-­
scope® is used exceeds the above RF compliance level, the e-­scope® should be observed to verify normal
operation. If abnormal performance is observed, additional measures may be required, such as reorienting or
shifting the e-­scope®.
b With a frequency range over 150 kHz to 80 MHz, the field strengths should be less than 3 V/m.
Recommended distances between portable and mobile RF communications equipment
The e-­scope® is intended for use in an electromagnetic environment in which RF emissions
are controlled. The customer or user of the e-­scope® can help to avoid electromagnetic
interference by observing the minimum distance between portable and mobile RF
communications equipment (transmitters) and the e-­scope® in accordance with the maximum
output power of the communication equipment.
Separation distance according to the frequency of the transmitter
Rated maximum
output power of the
transmitter (W)
0.01
0.1
1
10
100
For transmitters with a maximum output power not listed above, the recommended distance d
in metres (m) can be estimated using the equation for the transmitter frequency, where P is the
maximum output power of the transmitter in watts (W). according to the transmitter
manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance applies to the higher frequency
range.
NOTE 2 These guidelines may not apply in all situations. The electromagnetic propagation is
affected by absorption and reflection of structures, objects and people.
Compliance
Portable and mobile RF communications equipment
should not be used closer to any part of the non-­contact
e-­scope®, including the cables, than the recommended
Not applicable
distance, which is calculated using the equation
applicable to the transmitter frequency.
Recommended separation distance
d= 1.2√P 80 MHz to 800 MHz
d= 2.3√P 800 MHz to 2.7 GHz
Where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in metres (m).
Field strengths from fixed RF transmitters, as determined
by an electromagnetic site survey,
the compliance level in each frequency range.
Interference may occur in the vicinity of equipment
marked with the following symbol:
10 V/m
27 V/m
28 V/m
9 V/m
28 V/m
28 V/m
9 V/m
and the e-­scope®
(m)
150 KHz to 80 MHz
0.12 0.12
0.38 0.38
1.2 1.2
3.8 3.8
12 12
Electromagnetic environment -­ Instructions
a
should be less than
80 MHz to 800 MHz 800 MHz to 2.7 GHz
0.23
0.73
2.3
7.3
23
b
12
0,23
0,73
2,3
7,3
23
19