Technical Data - REMS Tornado 2000 Notice D'utilisation

g
Footswitch safety
Do not use this machine if the footswitch is broken or missing. Footswitch
is a safety device that provides better control by letting you shut off the motor in
various emergency situations by removing your foot from the switch. For example:
if clothing should become caught in the machine, the high torque will continue
pulling you into the machine. The clothing itself can bind around your arm or
other body parts with enough force to crush or break bones.
Additional Safety Instructions for Thread Cutting Machines
Only connect the machine of protection class I to a socket/extension lead
with a functioning protective contact. There is a danger of electric shock.
Check the power cable of the machine and extension leads regularly for
damage.
customer service workshop in case of damage.
The machine is operated by a safety foot switch with emergency stop in
inching mode. If you cannot see the danger area constituted by the revolving
workpiece from the operating point, set up protective measures, e.g. cordons.
There is a risk of injury.
Only use the machine for the intended purpose described in 1. Technical
Data. Work such as roping, assembling and disassembling, thread cutting with
manual die stocks, work with manual pipe cutters as well as holding workpieces
by hand instead of with material supports are prohibited when the machine is
running. There is a risk of injury.
If the risk of bending and uncontrolled lashing of the workpieces is to be
expected (depending on the length and cross section of the material and
the speed of rotation) or the machine is not standing stably enough (e.g.
able material supports REMS Herkules 3B (accessory, Art. No. 120120) must
be used. There is a risk of injury if you fail to do so.
Never reach into the revolving clamping or guide chuck. There is a risk of
injury.
Machine and/or tools can be damaged.
Thread cutting materials in spray cans (REMS Spezial, REMS Sanitol)
(butane). Aerosol cans are pressurised; do not open by force. Protect them
against direct sunlight and temperatures above 50°C. The aerosol cans can
burst, risk of injury.
Avoid intensive skin contact with the coolant-lubricants. These have a
degreasing effect. A skin protector with a greasing effect must be applied.
Only allow trained persons to use the machine. Apprentices may only use
the machine when they are over 16, when this is necessary for their training and
when they are supervised by a trained operative.

1. Technical Data

Use for the intended purpose
WARNING
Use REMS Tornado and Magnum thread cutting machines for the intended purpose of thread cutting, cutting off, removing burr, cutting nipples and roller grooves. All other
uses are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
REMS Tornado:
1.2. Article Numbers
Subframe
Wheel set with material rest
Subframe, mobile and folding
Subframe, mobile, with material rest
Dies
Universal automatic
die head ¹/
16
Universal automatic
Universal automatic
Tool set ¹/
16
Thread-cutting materials
Nippelhalter
REMS Herkules 3B
REMS Herkules Y
REMS roller groove device
All manuals and user guides at all-guides.com
Explanation of symbols
NOTICE
-
Thread cutting machine, tool set (¹/
16
material rest, oil tray, chip tray, opera ing instructions.
16
operating instructions.
16
Tornado 2000 Magnum 2000
Tornado 2010 Magnum 2010
Tornado 2020 Magnum 2020
344105 344105
344120 344120
344150 344150
344100 344100
see REMS catalogue see REMS catalogue
see REMS catalogue see REMS catalogue
see REMS catalogue see REMS catalogue
120120 120120
120130 120130
347000 347000
Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the machine
safely may not use this machine without supervision or instruction by a
responsible person. Otherwise there is a risk of operating errors and injuries.
Check the power cable of the electric al device and extension leads regularly
for damage.
customer service workshop in case of damage.
cient cable cross-section. Use extension leads with a cable cross-section of
at least 2.5 mm².
NOTICE
Do not dispose of thread-cutting material undiluted in the drain system,
ground water or ground. Unused thread-cutting material should be handed in
to responsible disposal companies. Waste code for thread-cutting materials
containing mineral oil (REMS Spezial) 54401, for synthetic materials (REMS
Sanitol) 54109. Observe the national regulations.
WARNING Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use eye protection
Use ear protection
Power tool complies with protection class I
Power tool complies with protection class II
Environmentally friendly disposal
CE conformity mark
Magnum 3000
Magnum 3010
Magnum 3020
344105
344120
344100
see REMS catalogue
see REMS catalogue
see REMS catalogue
120120
120130
347000
g
-
Magnum 4000
Magnum 4010
Magnum 4020
344105
344120
344100
see REMS catalogue
see REMS catalogue
see REMS catalogue
120120
120130
347000