Chicco Seat3Fit i-Size Notice D'emploi page 31

positioned correctly on the pelvic area.
• When adjusting the headrest check that the
diagonal belt guide (X) is located above the
shoulder at a maximum distance of 2 cm
(Fig. 44).
• Pull the diagonal portion of the belt toward
the retractor, so that the belt is tight and fits
snugly against the chest and legs of the child
(Fig. 45).
To install the car seat using the vehicle's 3-point
seat belt alone, proceed as follows:
• After having positioned the car seat on the
desired seat, run the diagonal segment of
the vehicle seat belt behind the headrest
and through the green diagonal belt guide
(X) (Fig. 46).
• Place the child in the car seat, verifying that
the child's back rests firmly against the back-
rest of the car seat.
• Fasten the vehicle seat belt to the buckle run-
ning the abdominal and diagonal segment
through the green belt guide (Y) (Fig. 47).
WARNING! When using the 3-point adult
safety belt, make sure that the lap portion is
positioned correctly on the pelvic area.
• When adjusting the headrest check that the
diagonal belt guide (X) is located above the
shoulder at a maximum distance of 2 cm
(Fig. 48).
• Pull the diagonal portion of the belt toward
the retractor, so that the belt is tight and fits
snugly against the chest and legs of the child
(Fig. 49).
8. REDUCER CUSHION
The car seat is equipped with a reducer cush-
ion to be used from birth to 75 cm, attached
to the car seat's headrest with two buttons
(Fig. 50).
9. ADJUSTING THE HEADREST AND HAR-
NESSES
The height of the headrest and restraint har-
nesses can be simultaneously adjusted by us-
ing the headrest adjustment ring (G).
40-105 cm:
Slacken the car seat harnesses using the ad-
justment button (E) while taking hold of the
two harnesses below the shoulder straps and
pulling toward yourself (Fig. 12). Next, pull up
on the adjustment ring (G) located above the
headrest (Fig. 51) and move the headrest to
the desired position; now release the ring and
ease the headrest until a click is heard, indi-
cating that it is locked correctly into position.
WARNING! To adjust them correctly, the
headrest must be fitted so as to allow that the
harnesses come out from the backrest at the
height of the child's shoulders (Fig. 52).
WARNING! Do not over-tighten the harnesses
around the child: If you can insert one finger
between the harness and your child's shoul-
ders, it means that it is tightened correctly.
100-125 cm:
To adjust the car seat headrest, use the adjust-
ment ring (G) located above the headrest (Fig.
51) and move the headrest until you reach
the desired position; now release the ring and
ease the headrest until a click is heard, indi-
cating that it is locked correctly into position.
WARNING! To adjust them correctly, the
headrest must be fitted so as to allow that the
harnesses come out from the backrest at the
height of the child's shoulders (Fig. 44).
10. ADJUSTING THE INCLINATION OF THE
CHILD CAR SEAT
The car seat can recline in 6 positions, 4 for-
ward facing and 2 rear facing. To adjust the in-
clination of the child car seat, pull the reclining
lever (J) (Fig. 53).
When installed in the rear facing position the
car sear must be reclined in positions 0 or 1
(Fig. 54), whereas when it is installed in the
forward facing position it can be reclined in
positions 2, 3, 4 or 5 (Fig. 55).
11. ROTATION
The car seat is equipped with a system that
allows for 360° of rotation by activating the
button (K).
The intermediate position at 90° can be used to
simplify the task of seating the child in the car seat.
WARNING! Do not use the intermediate 90°
position when the car is moving.
31