Scheppach DP16PRO Traduction De La Notice Originale page 21

specialist workshop unless otherwise indicated
in the instructions.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use power tools if the switch cannot be
turned on and off.
• CAUTION!
- The use of other bits and other accessories can
result in a risk of personal injury.
• Have your power tool be repaired by a quali-
fied electrician
- This power tool complies with the relevant safety
regulations. Repairs may only be performed by a
qualified electrician, using original spare parts;
otherwise accidents involving the user may result.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Service:
Have your power tool repaired only by qualified
•
specialists and only with original spare parts.
This will ensure that the power tool remains safe.
Safety instructions for drill press
Never make the warning labels on the power
•
tool illegible.
Attach the power tool to a solid, flat and hori-
•
zontal surface. If the power tool can slip or wob-
ble, the bit may not be guided smoothly and safely.
Keep the work area clean except for the work-
•
piece to be machined. Sharp-edged drilling chips
and objects can cause injury. Material mixtures
are particularly dangerous. Light metal dust can
burn or explode.
Set the correct speed before starting work. The
•
speed must be appropriate for the drill diam-
eter and the material to be drilled. At an incor-
rectly set speed the bit may get jammed in the
workpiece.
Only move the bit against the workpiece when
•
the device is turned on. Otherwise there is a
danger that the bit will get jammed in the work-
piece and the workpiece will rotate with the bit.
This can lead to injuries.
Do not put your hands in the area of the drill
•
while the power tool is running. Upon contact
with the bit there is a risk of injury.
Never remove drilling chips from the drilling
•
area while the power tool is running. Always
put the drive mechanism in the standby position
first and then turn on the power tool.
Do not remove accumulated drill chips with
•
your bare hands. There is a risk of injury due to
hot and sharp metal shavings in particular.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
All manuals and user guides at all-guides.com
Break up long drilling chips by interrupting the
•
drilling operation with a short backward rota-
tion of the rotary wheel. Long drilling chips may
cause injury.
Keep handles dry, clean and free from oil and
•
grease. Greasy, oily handles are slippery and lead
to loss of control.
Use clamps to hold the workpiece in place. Do
•
not work on any workpieces that are too small
for clamping. If you hold the workpiece by hand,
you cannot hold it sufficiently tightly against rota-
tion and may hurt yourself.
Switch the power tool off immediately if the bit
•
jams. The bit jams when:
- the power tool is overloaded or
- the workpiece to be machined is jammed.
Do not touch the bit after working before it has
•
cooled down. The bit is very hot during use.
Inspect the cable regularly and have a dam-
•
aged cable repaired only by an authorised cus-
tomer service centre. Replace damaged exten-
sion cables. This will ensure that the power tool
remains safe.
Store unused power tools in a safe place. The
•
storage place should be dry and lockable. This
prevents the power tool from being damaged as
a result of being stored or operated by inexperi-
enced people.
Never leave the tool before it has come to a
•
complete standstill. After running bits can cause
injury.
Do not use the power tool with a damaged ca-
•
ble. Do not touch the damaged cable and pull
the mains plug if the cable is damaged while
working. Damaged cables increase the risk of
electric shock.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and your
cidents using suitable precautionary measures!
Do not look directly into the laser beam with un-
•
protected eyes.
Never look into the path of the beam.
•
Never point the laser beam towards reflecting sur-
•
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
Caution - methods other than those specified here
•
can result in dangerous radiation exposure.
Never open the laser module. Unexpected expo-
•
sure to the beam can occur.
If the mitre saw is not used for an extended period
•
of time, the batteries should be removed.
The laser may not be replaced with a different type
•
of laser.
environment from ac-
GB / 21