Gaggia Milano CAREZZA Mode D'emploi page 34

- Wash the upper part of the Pannarello with fresh drinking
water.
- Wash the steam wand with a wet cloth and remove any
milk residue.
- Refi t the upper part in the steam wand (make sure it is
completely inserted).
After cleaning, reassemble the external part of the
29
Pannarello and make sure it reaches its limit stop. Make
also sure that the plastic part is correctly fi t in the metal
part.
• 31 Empty and wash the drip tray daily.
• Use a soft, dampened cloth to clean the appliance.
• 20 Clean the pressurized fi lter holder as follows:
- Remove the fi lter and wash it thoroughly with hot
9
water.
- Remove the adapter (if fi tted), and wash it thoroughly
with hot water.
- Wash the internal part of the pressurized fi lter holder.
• Do not dry the machine and/or its parts using a microwave
and/or standard oven.
Note: do not wash the pressurized fi lter holder
in the dishwasher.
12 Descaling
Limescale is a natural part of the water used for machine op-
eration. It needs to be removed regularly as it may clog the
water and coff ee circuit of your appliance.
This is an easy procedure for your Gaggia machine. When the
" " light (19) turns on, a descaling cycle is recommended.
When the " " light (19) starts blinking, descaling is com-
pulsory.
This operation needs to be carried out before
the appliance stops working properly, as in this
case repair is not covered by warranty.
Use the Gaggia descaling product (Fig. B). Its
formula has been designed to ensure better
machine performance and operation for its whole op-
erating life. If correctly used, it also avoids alterations
in the brewed product. Before starting a descaling cy-
cle make sure that: THE WATER FILTER (if used) HAS BEEN
REMOVED.
Never drink the descaling solution or any prod-
ucts dispensed until the cycle has been fully car-
ried out. Never use vinegar as a descaling solution.
• 34 •
1 13 14 Insert the fi lter holder (21) into the brew unit (4)
from the bottom. Turn the pressurized fi lter holder from
left to right until it locks into place. Release the pressurized
fi lter holder grip. The handle will turn slightly to the left.
This movement guarantees optimum fi lter holder perfor-
mance.
2 1 Remove and empty the water tank.
3 Pour HALF the content of the Gaggia concentrated
2
descaling solution into the water tank, then fi ll the tank
with fresh drinking water up to the MAX level.
4 4 Turn on the machine by pressing the ON/OFF button
(11). The " " light (12) turns on.
5 Following the instructions provided in chapter 9 of
this manual, dispense 2 cups of water (about 150 ml each)
from the steam wand (Pannarello) and turn the machine
off by pressing the ON/OFF button (11); the "
turns off .
5 Let the descaling solution take eff ect for approx. 15-20
minutes with the machine turned off .
6 Turn on the machine by pressing the ON/OFF "
button (11).
5 Following the instructions provided in chapter 9 of
this manual, dispense 2 cups of water (about 150 ml each)
from the steam wand (Pannarello). Turn off the machine by
pressing the ON/OFF " " button (11) and leave it off for 3
minutes.
7 Repeat the operations described in step 6 until the water
tank is completely empty.
During this operation the pump is automati-
cally disengaged and the "
blinking: this is a normal behaviour of the machine.
Close the knob. Wait until the "
on before opening the knob again.
8 2 Rinse the water tank with fresh drinking water and fi ll
it up.
9 Place a container under the fi lter holder.
10 Turn on the machine by pressing the "
(11); press the " " button (13) and dispense the whole
content of the tank by means of the fi lter holder. Press the
" " button (13) again to stop the dispensing process.
11 2 Refi ll the tank with fresh water.
5 Place a large container (about 1 l capacity) under the
steam wand (Pannarello).
Open the water dispensing knob (3) by turning it clock-
wise and dispense the whole content of the water tank by
means of the steam wand (Pannarello).
12 After the water dispensing process is complete, close
6
the water dispensing knob (3) by turning it counter-clock-
wise.
" light (12)
"
" light (20) is
" light (14) is steady
" ON/OFF button