Tractel Davimast Manuel D'installation, D'entretien Et D'emploi page 18

NOTE
e uipme t must e take out o ser ice.
GB
1 2 .3 .6 . ec in t e all a e t
This chapter describes the procedure for checking the
Blocfor™ R fall arrest function.
a sa e e iro me t with o risk o alli
according to the following instructions:
1. Attach the fall arrest device to an anchor point
vertically at least 2 m from the ground;
2. ook a 10 k wei ht to the e d o the ca le, holdi
it in position; and
3. Drop the 10 kg weight.
4. The fall must be stopped in less than one metre (1
m) in relation to the initial position of the weight.
5. old the ca le, u hook the wei ht a d check the
rewinding of the cable in the Blocfor™ .
NOTE
a ter se eral olts, the product must ot e used a d
must be returned to Tractel
1 2 .3 .7 . ec in t e e c e li tin
This chapter describes the procedure for checking the
Blocfor™ R lifting rescue function.
a sa e e iro me t with o risk o alli
according to the following instructions:
1. Install the Blocfor™
vertical position;
2. Unwind the cable and connect a 150 kg weight to
the end of the cable;
3. Engage on the Blocfor™
button;
4. Lift the 150 kg weight using the crank handle;
5. Release the crank handle; the locking must be done
immediately without slipping;
CAUTION: The crank handle can move suddenly.
6. Wait three minutes; and
7. Bring the weight back down.
NOTE the locki
a ter se eral olts or i the wei ht oes dow
three mi ute delay, the product must ot e used a d
must be returned to Tractel
1 2 .4 . ec in t e a ol
The Carol™ TS winch is supplied with its Davimast
bracket and its cable.
18
o e o these situatio s de elops, the
nction
the lock is ot immediate, i it occurs
or an authorised repairer.
®
te
R on an anchor point in a
winch by pushing the red
is ot immediate, i it occurs
or an authorised repairer.
®
TS inc
Position the Carol™
inspected from all sides.
1 2 .4 .1 . ec in t e
The Carol™
at least:
• The manufacturer's or supplier's name;
, proceed
• The CE label;
• The e uipme t re ere ce
• The batch or serial number;
• The e uipme t sta dard ollowed y the year o
reference; and
• The logo; read the instruction manual.
NOTE
e uipme t must e take out o ser ice.
1 2 .4 .2 . ec in t e co p l o
p e ent
The Carol™
• Its Davimast bracket;
• A Carol™
• The winch with all its components; crank handle arm
and plastic handle.
1 2 .4 .3 . ec in t e ene al con ition o t e
a ol
Inspect each side of the Carol™
, proceed
speci cally check whether
• The housings are deformed;
• The crank handle and plastic handle are deformed;
• The incorrect wound or unwound of the whole cable;
• There is any corrosion;
• A y pi s, screws or ri ets are missi
NOTE
e uipme t must e take out o ser ice.
1 2 .4 .4 . ec in t e ene al con ition o t e ca le
See chapter 12.2,
check.
The e d o the ca le must e e uipped with a hook
which also needs to be checked.
1 2 .4 .5 . ec in t e p ope
a ol
e ore the
a sa e e
according to the following instructions:
Install the Carol™
Davimast.
To check the correct operatio o the lock, use a 2
weight attached to the end of the cable.
TS winch so that it can be
a in
TS winch must have the following markings
a y marki oes missi
co ponent a e
TS winch must have the following at least:
TS cable;
TS inc
TS winch and more
o e o these situatio s de elops, the
hecki the ca le, to per orm the
nctionin o t e
TS inc
iro me t with o risk o alli
TS winch with its bracket on the
, the a ected
.
, proceed
k